ESD-ABS
Effective Date: 08/01/2022
Revision Number: V1.1
1. Product and Supplier Information
| Product Name | ESD-ABS |
|---|---|
| Product Use | 3D Printing Filament |
| Manufacturer/Supplier | Rev1Tech, 904 36th Street, Suite B, Grand Rapids, MI 49500, USA |
| Address | 2901 Auburn Rd, Auburn Hills, MI 48326 |
| Contact Email | [email protected] |
| Telephone | +248-707-2950 |
| Emergency Telephone Number | +248-707-2950 |
2. Hazards Identification
Regulation (EC) NO 1272/2008: Not classified as a dangerous product
Physical Hazards: None
OSHA Regulatory Status: This product is not considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
3. Composition/Information on Ingredients
| Component | CAS No. | Concentration Range (%) |
|---|---|---|
| ABS Resin | 9003-56-9 | >90 |
| Carbon Additives | 1333-86-4 | <10 |
4. Emergency First Aid
- Eyes: Flush with water. Consult physician if symptoms persist.
- Skin Contact: Wash with soap and water. For thermal burns from molten polymer, immediately flush with cold water. Do not attempt to remove cooled polymer from skin. Obtain medical attention.
- Inhalation: Leave exposed area and seek fresh air. If irritation persists seek medical attention.
- Ingestion: Not likely due to nature of product. If ingested, drink plenty of water. Do not induce vomiting. Consult a physician if symptoms persist.
5. Fire and Explosion Hazard
Extinguishing Media: Water spray, dry powder, foam, carbon dioxide (CO2)
Safety Precautions: Persons exposed to products of combustion should wear NIOSH approved self-contained breathing apparatus and full protective equipment.
6. Accidental Release Measures
Spill or Release: Clean up by vacuuming or sweeping to prevent falls. If molten, allow material to cool and place into an appropriate container for disposal.
7. Handling and Storage Conditions
Precautions to be taken in handling and storage: Store in a dry, sprinkler-equipped warehouse. Product as shipped is not a combustible dust. Mechanical handling can cause the formation of dusts. To reduce the risk for dust explosion do not permit dust to accumulate.
Waste Disposal: Dispose in accordance with applicable federal, state and local regulations.
8. Exposure and Protection Information
Exposure Limits: This product does not contain any hazardous materials with occupational exposure limits established by the region-specific regulatory bodies.
Respiratory Protection: A NIOSH approved respirator is recommended for protection against processing polymeric fumes, or from dust generated from grinding, sanding, or sawing operations.
Ventilation: Local exhaust is preferred.
Protection Gloves: Canvas or cotton gloves are recommended.
Eye Protection: Safety glasses with side shields are recommended.
Other: No protective equipment is needed under normal use conditions.
9. Physical/Chemical Data
| Form | Solid |
|---|---|
| Appearance | Black Filament |
| Odor | Slight |
| Freezing Point | N/A |
| Solubility in Water | Insoluble |
| Specific Gravity | >1 |
| % Volatile | N/A |
| Boiling Range | N/A |
| Vapor Pressure (MM HG) | Negligible |
| Melting Point | This product does not possess a specific melting point. It softens gradually over a wide temperature range. |
Note: Those physical data are typical values based on material tested but may vary from sample to sample. Typical values should not be construed as a guaranteed analysis of any specific lot or as specifications for the product.
10. Stability and Reactivity
Polymerization conditions to avoid: None
Chemical Stability: Stable under normal conditions
Conditions to avoid: Incompatible materials, including strong oxidizing agents
Hazardous decomposition byproducts: Thermal decomposition can yield intense heat, dense smoke, phenols, hydrogen cyanide, carbon dioxide, and carbon monoxide.
11. Toxicological Information
No specific toxicological information is available.
12. Ecological Information
No specific ecological information is available.
13. Disposal
Waste Disposal: Waste or unused product may be discarded in accordance with state, federal, and local regulations.
14. Transport Information
Land Transport (DOT): Non-Regulated
Click here to shop 3dxstat ESD ABS.