MEDICAL PRODUCTION CELL • FORMLABS • REV1 TECH

Formlabs Form 4B Premium Back-to-Back Cases, Fully Equipped

Two Flex Build Platforms and two Form Wash V2 units, plus Form Cure V2 and a 5-year Dental and Medical Service Plan.

Formlabs Form 4B Premium Package: Form 4B with two Form Wash V2 units and Form Cure V2

The Formlabs Form 4B Premium Package is set up for back-to-back cases: the Form 4B printer with two Flex Build Platforms and two Form Wash V2 units so one build washes while the next prints, a Solvent Pump, Form Cure V2, the Form 4 Finish Kit, and a 5-year Form 4B Dental and Medical Service Plan. The printer at its core is Form 4B: the Low Force Display™ engine with a 50 µm pixel, validated for Formlabs’ biocompatible BioMed and dental resins. Full specifications →

200×125×210Build Volume (mm)
50 µmXY Pixel Size
100 mm/hrMax Print Speed
98.7%Print Success Rate
Print Engine
Low Force Display™405 nm60-LED Backlight16 mW/cm²
BioMed Resins
BioMed ClearBioMed DurableBioMed AmberBioMed White & BlackFlex 80A & Elastic 50A
Automation
Auto Resin Dispensing6 Control SystemsZ-Axis Force Sensing5MP Camera
Software
PreFormDashboardForm Mobile App

Authorized Formlabs reseller in the USA — Rev1 helps clinical and device teams choose the right package, BioMed resins, and post-processing. Questions? Call (248) 707-2950.

Formlabs Form 4B Premium Package: Form 4B with two Form Wash V2 units and Form Cure V2
Rev1 Technologies · Authorized Formlabs Partner

Factory-Built Precision. US-Supported by Rev1.

Every Form 4B passes a 60-point calibration and quality-control inspection before it leaves the Formlabs factory, and BioMed resins are made in Formlabs’ FDA-registered, ISO 13485-certified facility. Rev1 adds application review, resin selection, onboarding, and US-based support from Auburn Hills, Michigan.

Authorized Formlabs Reseller 60-Point Factory Calibration Dental & Medical Service Plans
Formlabs — official manufacturer of the Form 4B
FormlabsOfficial Manufacturer
Rev1 Technologies — authorized Formlabs reseller, Auburn Hills MI
Rev1 TechnologiesAuthorized Reseller
Why Choose the Form 4B

Quality you can trust when it matters most — at a speed that keeps up with surgery schedules.

Point-of-care teams, medical device manufacturers, and dental labs need parts that are accurate, repeatable, and made from materials with documented biocompatibility. Form 4B pairs Formlabs’ fastest resin engine with the BioMed resin family, so a cutting guide or sizing trial is on the table the same morning it was planned.

4× Faster Than Form 3B+
Formlabs measured up to four times the speed and 30% more build volume than Form 3B+. A surgical sizing trial averages 4 minutes per part on Form 4B versus 26 minutes on Form 3B+.
Biocompatible BioMed Resins
BioMed Clear, Durable, Amber, White, Black, Flex 80A, and Elastic 50A are made in an FDA-registered, ISO 13485-certified facility, with skin, mucosal, bone, and tissue contact ratings by material.
Surgical-Grade Accuracy
Highly collimated light and a 50 µm pixel with pre-tuned anti-aliasing deliver consistent accuracy across the whole build platform — and the smoothest surfaces Formlabs has printed.
98.7% Print Success
An independent global leader in product testing measured Form 4B at a 98.7% print success rate. Validated settings, six control systems, and factory calibration keep critical cases on schedule.
A Workflow Built for Sterile Use
Prepare, print, wash, cure, then finish, sterilize, and package. BioMed parts are compatible with common solvent disinfection and sterilization methods, depending on the material.
Medical-Grade Support
The Formlabs Dental and Medical Service Plan adds personalized onboarding, unlimited access to medical experts, replacement parts, and hot swaps — with Rev1 as your local partner.
Proven in Healthcare

Who prints on Form 4B — and what they say.

From orthopedic implant makers to hospital 3D printing labs, Form 4B users report the same thing: speed they had not seen from SLA before. Quotes are from Formlabs’ published Form 4B customer stories.

restor3D implant sizing trials on lattice supports printed on Formlabs Form 4B
restor3D — Orthopedic Implants
“In my eight years’ experience with additive manufacturing, I haven’t seen SLA machines print parts that quickly,” says Additive Manufacturing Manager Elena Tercheria.
RICOH 3D for Healthcare innovation studio with Formlabs printers
RICOH 3D for Healthcare
Ryan Hess, Senior Director of Innovation and Strategy, credits Formlabs with the best customer engagement his team has had in additive manufacturing, at a price point that lets them move fast.
Formlabs Form 4B beside a freshly printed anatomical model on supports
In-House Hospital Printing
Bringing printing in-house turns days of outsourcing into same-day models, guides, and trials — with the materials, settings, and records under your own quality system.
Low Force Display™ Print Engine

A print engine rebuilt from the light source up.

Form 4B is a masked stereolithography (MSLA) printer, but it does not behave like a typical LCD machine. Formlabs engineered six components — backlight, Light Processing Unit, release texture, flexible film tank, control systems, and resin handling — to work as one Low Force Display™ system.

Low Force Display™

Uniform, high-power light across the whole platform

The Backlight Unit projects ultra-high-power light from 60 LEDs through a plano-convex collimating lens array. Because the light arrives straight and uniform, a part printed in the corner cures exactly like a part printed in the center — the root of Form 4B’s speed and its consistency from one build to the next. Form 4B shares this engine with Form 4, and Formlabs’ engineering walkthrough of the Form 4 shows each component in motion.

Backlight60 LEDs + lens array
Wavelength405 nm
Cure-Plane Intensity16 mW/cm²
CoolingIntegrated air cooling
Light Processing Unit 4

50 µm masking with pre-tuned anti-aliasing

The Light Processing Unit 4 (LPU 4) masks the backlight into the exact shape of each layer at a 50 µm pixel size, with anti-aliasing tuned at the factory for sub-pixel edge resolution. Formlabs built the LPU 4 to be long-lasting, resistant to accidental damage, and simple to swap in the field, so the most-used optical component never becomes a reason for downtime.

50 µm pixel Sub-pixel anti-aliasing Damage-resistant User-replaceable
Release Texture

Lower peel forces, finer features, lighter supports

A proprietary micro-textured optical film sits on top of the LPU and lets air flow between the tank and the display. That dramatically reduces the suction each layer has to break as it lifts, so Form 4B can print fast without tearing delicate features or distorting thin walls. Lower forces also mean lighter, light-touch supports that snap away cleanly and leave smaller witness marks.

Micro-textured film Air-gap release Light-touch supports
Accuracy & Surface Finish

No compromises on the parts that go into the operating room.

3D printed anatomical ilium beside its color deviation map against the CT-derived model

Consistently accurate across the build platform

Formlabs scanned a 3D printed anatomical ilium and mapped it against the source model: the deviation map stays tight across the whole bone, not just at the center of the platform. That consistency comes from the collimated backlight — light reaches every pixel at the same angle and intensity, so a cutting guide in the corner fits as well as one in the middle.

50 µmXY pixel size
±0.15%1–30 mm features
25 µmFinest layer
Sharpest Details

Smooth surfaces and fine features, ready for sterilization

Lower peel forces, light-touch supports, and a 50 µm pixel with pre-tuned anti-aliasing leave smooth, consistent surfaces with crisp edges — from lattice cranial implants to thin-walled guides and masks. Less support scarring means less hand finishing before parts are cleaned, sterilized, and packaged.

Collimated light Sub-pixel anti-aliasing Light-touch supports Minimal finishing
Surgical team in scrubs reviewing a 3D printed anatomical model in front of patient scans

Anatomy surgeons can hold before they operate

Patient-specific models printed from CT and MRI data let surgical teams rehearse a complex case, check implant fit, and explain the procedure to patients. Accurate, smooth parts in BioMed White, Clear, or the flexible BioMed elastomers show bone, vessels, and soft tissue the way the team will see them in the operating room.

Surgical planning Implant fit checks Patient communication
Print Speed

Unprecedented throughput: 4× the speed and 30% more build volume.

Formlabs timed real medical parts on Form 4B, a benchmark DLP printer, a benchmark LCD printer, and the previous-generation Form 3B+. Times below are Formlabs’ published averages per part; the speed claim is relative to Form 3B+.

Form 4B build platform full of clear surgical sizing trials printed for restor3D

Surgical sizing trials: 4 minutes per part

restor3D prints full platforms of sizing trials so surgeons can confirm implant size in the operating room. On Form 4B each trial averages 4 minutes — faster than both benchmark DLP and LCD printers, and more than six times faster than Form 3B+. Because the whole layer cures at once, a full platform takes about as long as a single part.

4 minForm 4B
7 minBenchmark DLP
5 minBenchmark LCD
26 minForm 3B+
Form 4B build platform carrying a full-size 3D printed anatomical ilium on supports

Anatomical models: a full ilium in 3½ hours

Large anatomical models are where older printers stretch overnight. Insight Surgery’s anatomical ilium prints in 3 h 30 min on Form 4B, against 8 h 14 min on a benchmark DLP printer and nearly 15 hours on Form 3B+ — so a model requested in the morning is in the surgeon’s hands the same afternoon.

3 h 30 mForm 4B
8 h 14 mBenchmark DLP
3 h 40 mBenchmark LCD
14 h 52 mForm 3B+
Form 4B build platform with a batch of orthopedic cutting guides for Insight Surgery
Orthopedic Cutting Guide — 7 min/part
Insight Surgery’s patient-specific guides: 7 minutes on Form 4B, 8 on a benchmark LCD, and 38 on Form 3B+.
Form 4B build platform with fibula free flap surgical models on lattice supports
Fibula Free Flap — 2 h 27 min
TechFit’s reconstruction models: 2 h 27 min on Form 4B versus 4 h 6 min (DLP) and 7 h 36 min (Form 3B+).
Form 4B build platform with surgical ratchet handles printed upright
Surgical Ratchet — 44 min
Formlabs’ surgical ratchet: 44 minutes on Form 4B, 1 h 1 min on a benchmark DLP printer, and 3 h 51 min on Form 3B+.
Watch the Demo
Form 4 Series in Motion

The engine behind Form 4B, in a few minutes

Formlabs’ launch video for the Form 4 series — which Formlabs features on its Form 4B page — walks through the Low Force Display engine, automatic resin handling, and the speed gains that carry straight over to Form 4B.

Resin Handling & Control Systems

The printer manages the resin, so you don’t have to.

Automatic Resin Handling

Snap in a cartridge, switch materials in under a minute

Resin Cartridge V2 docks in the back of the printer and dispenses resin quickly and precisely as the print needs it — no pouring, no running dry mid-job, minimal waste. Changing materials is a cartridge and tank swap that takes less than a minute, which makes it practical to run several resins through one printer in a single day. Formlabs notes Form 4B remains one of the only SLA printers on the market with automatic resin dispensing.

Filling Speed5–10× faster (V2)
Resin Waste63% less
Shelf Space30% less
Material Change< 1 minute
Flexible Film Resin Tank

A dual-layer film tank rated for 75,000+ layers

The Form 4 Resin Tank holds the liquid resin and gives each layer a surface to cure against, using a dual-layer flexible film stack that works with the release texture to keep peel forces low. Formlabs rates each tank for more than 75,000 layers with any Formlabs material — roughly 190 prints of an average 39 mm-tall model at 100 µm — and the built-in mixer keeps resin homogeneous between layers.

Dual-layer film stack 75,000+ layer lifetime Built-in mixer Per-material tanks
Intelligent Control Systems

Six sensors watching temperature, level, and force

Six upgraded onboard control systems measure and hold the conditions every material is validated against. High-speed conduction heating with infrared sensing brings resin to its target temperature; an ultrasonic sensor manages the tank level; a load cell tracks exactly how much resin remains in the cartridge; and a Z-axis force sensor adjusts print speed to the part geometry and material in real time.

Resin Heating25–45 °C, IR sensing
Tank LevelUltrasonic level sense
CartridgeLoad cell
Print ForcesZ-axis force sensor
Reliability

Stop coming back to failed prints.

Formlabs states Form 4B was measured at a 98.7% print success rate by an independent global leader in product testing. When a print supports a scheduled surgery, these are the systems that keep it on time.

Factory Calibration & Validated Settings

Calibrated before it ships, tuned for every resin

Each printer goes through a 60-point calibration and quality-control inspection at the factory. Formlabs optimization engineers then validate print settings for every material by putting hundreds of printed parts to the test, so each resin performs to the same standard right out of the box — on every Form 4B in a fleet.

98.7%Print success rate
60-pointFactory calibration
Remote Monitoring

Watch, manage, and get alerted from anywhere

An integrated 5MP camera (2592 × 1944) records print history and timelapses and streams job status to Formlabs Dashboard and the Form Mobile App. Dashboard sends SMS and email alerts, tracks resin and tank usage, and issues preventative-maintenance reminders. For secure facilities, the camera can be disabled, covered, or removed.

5MP camera Timelapses SMS & email alerts Camera removable
Long-Lasting Consumables

Hardware engineered for years of daily use

Form 4B’s wear parts were designed for longevity and quick replacement. The LPU 4 resists accidental damage and swaps without tools expertise, resin tanks last 75,000+ layers, and Resin Cartridge V2 stores in less space with less waste — so cost per part stays predictable as utilization climbs.

Durable LPU 4 Long-life tanks Predictable cost per part
Right machine for your parts?
Not sure the Form 4B fits your clinical application?
Send us your case or device — Rev1 reviews BioMed resin choice, throughput, and post-processing and sterilization steps before you commit. Free, no purchase required.
BioMed & Dental Resins

Effortlessly create parts for any medical application.

Biocompatible materials are the reason to choose Form 4B: the standard Form 4 cannot print them. BioMed resins are manufactured in Formlabs’ FDA-registered, ISO 13485-certified facility, and each has its own contact rating — always confirm the material against your device’s intended use. Form 4B also runs Formlabs’ dental resin library (see Formlabs Dental) and every standard Formlabs resin. Browse Rev1’s 3D printing resins.

BIOMED CLEAR
BioMed Clear Resin
Transparent, hard, and wear-resistant. Rated for long-term skin (>30 days), breathing-gas pathways, and mucosal contact (>30 hours), or short-term bone, tissue, and dentin contact (<24 hours).
USP Class VI · transparent
BIOMED DURABLE
BioMed Durable Resin
Transparent and impact-, shatter-, and abrasion-resistant for devices that take abuse: long-term skin and mucosal contact, short-term tissue, bone, and dentin contact.
USP Class VI · impact-resistant
BIOMED AMBER
BioMed Amber Resin
Strong and stiff for surgical guides and instruments: long-term skin contact or short-term bone, tissue, dentin, and mucosal contact, and compatible with common sterilization methods.
Rigid · 73 MPa tensile
BIOMED WHITE
BioMed White Resin
A rigid, opaque white material for anatomical models, guides, and device components, rated for long-term skin or short-term bone, tissue, dentin, and mucosal contact.
USP Class VI · rigid white
BIOMED BLACK
BioMed Black Resin
Rigid and matte for end-use device housings, masks, and wearables: long-term skin or short-term mucosal contact, with common disinfection and sterilization methods.
USP Class VI · matte black
BIOMED FLEX
BioMed Flex 80A Resin
Firm, flexible, and transparent for durable soft parts and realistic anatomy such as this diseased aorta model: long-term skin or short-term mucosal contact.
Shore 80A · 135% elongation
BIOMED ELASTIC
BioMed Elastic 50A Resin
A soft, compliant elastomer for flexible anatomy and cushioning components — like this translucent heart model used to plan and explain procedures.
Shore 50A · soft-touch
Parts printed in Formlabs General Purpose resins: architectural model, helmet, camera prototype, and color samples
ENGINEERING
Full Formlabs Resin Library
Form 4B also prints every standard Formlabs material — general purpose, tough, rigid, flame retardant, silicone, and more — for device prototypes, fixtures, and test rigs.
Prototype to production
Third-party photopolymer being measured out for printing in Formlabs Open Material Mode
OPEN MATERIAL
Open Material Mode
Run qualified third-party 405 nm photopolymers with customizable settings when a specialty medical or research chemistry is required.
Any 405 nm photopolymer
Software

PreForm, Dashboard, and the Form Mobile App — included, free.

PreForm prepares every job: One-Click Print, auto-orientation, automatic support generation with advanced manual editing, auto mesh repair, adaptive layer thickness, and a layer slicer for inspection. It imports STL, OBJ, 3MF, and native CAD formats on Windows 10 (64-bit) and macOS 13 or later. Dashboard manages prints and printers through the cloud, tracks resin and tank usage, and supports enterprise group accounts with admin controls, while the Form Mobile App pushes job notifications to your phone.

Formlabs PreForm software on a laptop preparing a supported Form 4B print job
Print Workflow

The same trusted workflow, now four times faster.

The Form 4B workflow is four steps from scan-derived model to a part that is ready for the clinic: prepare, print, wash and cure, then finish, sterilize, and package.

1 · Prepare
Import your model into PreForm. Smart auto-orientation, advanced support generation, and live printability checks set up the job.
2 · Print
Load a cartridge and click print. Validated settings and automatic resin dispensing take it from there.
3 · Wash & Cure
Quick-release part removal, automatic cleaning in Form Wash, and precision post-curing in Form Cure — essential for BioMed resins to reach their rated properties.
4 · Finish & Sterilize
Light-touch supports remove quickly and cleanly. Refine surfaces with Formlabs Finishing Tools, then sterilize and package per your validated process.
Workflow Overview

Design to finished part, start to finish

Formlabs’ Form 4/B workflow overview follows a job from design through PreForm setup, printing, washing, curing, and support removal. Rev1 runs the same walkthrough during onboarding and helps your team document wash, cure, and sterilization steps for each BioMed resin.

Configurations

Three Form 4B packages, each with Dental and Medical support.

Each package has its own page, just as on Formlabs’ store — switch with the Package selector above. Every Form 4B package ships with a Flex Build Platform; Complete and Premium add Form Wash and Form Cure and a multi-year Formlabs Dental and Medical Service Plan.

Form 4 Series resin tank included with the Form 4B Basic Package
BASIC PACKAGE · $7,699
Form 4B Basic
Form 4B printer, Resin Tank, Mixer, Flex Build Platform, and Finish Kit — for labs that already own wash and cure equipment. Dental and Medical Service Plans can be added.
SKU PKG-F4B-BASIC
View the Basic Package →
Formlabs Form 4B Complete Package: Form 4B with Form Wash V2 and Form Cure V2
COMPLETE PACKAGE · $12,045
Form 4B Complete
Everything in Basic plus Form Wash V2, Solvent Pump, Form Cure V2 (120 V), and a 3-year Form 4B Dental and Medical Service Plan.
SKU PKG-F4B-COMPLETE-120V
View the Complete Package →
Formlabs Form Cure V2 post-cure unit included in the Form 4B Premium Package
PREMIUM PACKAGE · $14,333
Form 4B Premium
Two Flex Build Platforms and two Form Wash V2 units for back-to-back cases, Solvent Pump, Form Cure V2, and a 5-year Form 4B Dental and Medical Service Plan.
SKU PKG-F4B-PREMIUM-120V
You are viewing this package
In the Box

The Form 4B Premium Package includes:

Form 4B Printer Form 4 Resin Tank Form 4 Mixer Form 4 Flex Build Platform × 2 Form 4 Finish Kit Form Wash V2 × 2 Solvent Pump Form Cure V2 (120 V) Form 4B Dental and Medical Service Plan — 5 Years
Compare

Form 4B vs. Form 4: same engine, different mission.

The most common question we get is whether a medical team needs the B. The hardware is the same; the difference is which materials and support the printer is cleared to run. Figures are from Formlabs’ published specifications and US store.

CapabilityFormlabs Form 4BFormlabs Form 4
Print engineLow Force Display™ (MSLA)Low Force Display™ (MSLA)
Build volume200 × 125 × 210 mm (5.3 L)200 × 125 × 210 mm (5.3 L)
XY pixel size50 µm, pre-tuned anti-aliasing50 µm, pre-tuned anti-aliasing
Print success rate98.7% (independent lab)98.7% (independent lab)
Biocompatible BioMed resinsYesNo (available on Form 4B)
Dental resinsYesNo
Service planDental and Medical Service PlanPro Service Plan
Build platform in Basic PackageFlex Build PlatformStandard Build Platform
Basic Package price$7,699$2,625

If your parts never touch a patient, the Formlabs Form 4 prints the same geometry for less. For large anatomical models and full-size guides, ask about the Form 4BL, or compare the Formlabs Form 4L. Browse all SLA printers and Rev1’s industrial 3D printer range.

Planning a point-of-care lab?
Configure the Form 4B for your clinical workflow
Tell us your case volume, materials, and sterilization process — Rev1 confirms the right package, BioMed resins, and post-processing before you buy.
Specifications

Formlabs Form 4B Technical Data

Technology
Masked Stereolithography (MSLA)
Print Engine
Low Force Display™ (LFD)
Light Source
Backlight Unit: 60 LEDs, plano-convex lens array, air cooled
Wavelength / Intensity
405 nm · 16 mW/cm² at the cure plane
XY Resolution
50 µm pixel, pre-tuned anti-aliasing
Build Volume (W×D×H)
20.0 × 12.5 × 21.0 cm (7.9 × 4.9 × 8.3 in) · 5.3 L
Build Area / Max Part Length
250 cm² · 27.3 cm
Layer Thickness
25–200 µm (0.001–0.008 in)
Print Speed
Up to 100 mm/hr · up to 4× faster than Form 3B+
XY Tolerances
±0.15% (1–30 mm) · ±0.2% (31–80 mm) · ±0.3% (81–150 mm)
Reliability
98.7% print success (independent lab)
Materials
BioMed biocompatible resins, Formlabs dental and standard resins + Open Material Mode (405 nm)
Resin Handling
Automatic dispensing · 1× Resin Cartridge V2
Resin Heating
Conduction heating, IR sensing · 25–45 °C
Sensors
Ultrasonic level, cartridge load cell, Z-axis force, leveling, camera
Camera
5MP (2592 × 1944), removable
Printer Control
7″ touchscreen, 1280 × 800
Connectivity
Wi-Fi 2.4/5 GHz · Ethernet 1000 Mbit · USB-C 2.0
Software
PreForm, Dashboard, Form Mobile App
Power
100–240 VAC · 4.8 A · 50/60 Hz · 480 W
Dimensions / Min. Access
39.8 × 36.7 × 55.4 cm · access 40.7 × 47.8 × 84.4 cm
Weight / Environment
18.3 kg (40.4 lb) · 18–28 °C operating

RESOURCES

Downloads & Technical Support

Everything you need to qualify and run your Formlabs Form 4B with confidence.

Form 4 Series Sell Sheet
Formlabs’ Form 4 series overview: the LFD print engine, post-processing, and specifications shared by Form 4B (PDF).
Download PDF →
BioMed Resin Data & Workflow
BioMed technical data sheets, biocompatibility documentation, and wash, cure, and sterilization guidance for Form 4B.
Rev1 Technical Support
Application review, sample prints, and post-sales engineering guidance from Rev1 Technologies.

WHY REV1 TECH

Authorized Formlabs Reseller. Medical & Resin Workflow Specialists.

Rev1 Technologies is headquartered in Auburn Hills, MI, with direct expertise in production resin workflows.

YOUR REV1 PARTNER
AUTHORIZED FORMLABS RESELLER
01
Application Engineering
We review your cases and devices and recommend the right BioMed resins and Form 4B package before your printer arrives.
02
Onboarding & Training
Rev1 handles setup and operator training on PreForm, Dashboard, and the print-to-post workflow.
03
Ongoing Support
Direct access to Rev1’s technical team for resin guidance, troubleshooting, and maintenance.
04
Free Sample Print
Send us your STL. We’ll print a sample on Formlabs SLA in a suitable resin and ship it to you — or get an instant print quote.
05
In-Person Demo
Visit our Auburn Hills facility or schedule a demo at your site.
06
Consumables & Parts
BioMed and standard Formlabs resins, resin tanks, build platforms, and replacement LPUs — sourced and supported from the USA.
Buyer FAQ

Formlabs Form 4B — questions medical and dental buyers ask.

What is the difference between Form 4B and Form 4?
Form 4B uses the same Low Force Display print engine, build volume, and 50 µm pixel as Form 4. The B is validated for Formlabs’ biocompatible BioMed resins and dental resins, which the standard Form 4 cannot print, and it is supported by the Formlabs Dental and Medical Service Plan.
Which biocompatible resins can Form 4B print?
BioMed Clear, BioMed Durable, BioMed Amber, BioMed White, BioMed Black, BioMed Flex 80A, and BioMed Elastic 50A, plus Formlabs’ dental resins and every standard Formlabs material. Third-party 405 nm resins run in Open Material Mode.
Are BioMed parts approved for patient contact?
Each BioMed resin carries its own biocompatibility ratings — for example long-term skin contact or short-term bone, tissue, and mucosal contact — and several are USP Class VI certified. Ratings apply when parts are printed, washed, cured, and post-processed per Formlabs’ instructions; your organization remains responsible for validating the finished device.
Can Form 4B parts be sterilized?
Formlabs states BioMed parts are compatible with common solvent disinfection and sterilization methods, with the specific methods listed on each material’s data sheet. Rev1 helps you document the wash, cure, and sterilization steps for your process.
How much faster is Form 4B than Form 3B+?
Formlabs measured up to four times the speed with 30% more build volume. Published per-part averages include 4 minutes versus 26 minutes for a surgical sizing trial and 3 h 30 min versus 14 h 52 min for an anatomical ilium.
How reliable is Form 4B?
Formlabs reports a 98.7% print success rate measured by an independent global leader in product testing, backed by six onboard control systems, validated print settings for each material, and a 60-point factory calibration.
What is in the Basic, Complete, and Premium packages?
Basic is the printer with Resin Tank, Mixer, Flex Build Platform, and Finish Kit ($7,699). Complete adds Form Wash V2, Solvent Pump, Form Cure V2, and a 3-year Dental and Medical Service Plan ($12,045). Premium doubles the Flex Build Platforms and Form Wash units and includes a 5-year plan ($14,333).
What does the Dental and Medical Service Plan include?
Formlabs’ medical service plan covers personalized onboarding, unlimited access to medical experts, replacement parts, and hot swaps. It is included for 3 or 5 years in the Complete and Premium packages and can be added to the Basic Package.
What if I need larger anatomical models or guides?
Form 4BL brings the same LFD technology to a large-format build volume and completes full-volume prints in under six hours. It shares BioMed materials and PreForm workflows with Form 4B, so a mixed fleet runs on one validated process.

READY FOR THE CLINIC

Bring the Formlabs Form 4B into your lab

Add the Form 4B Premium Package to your cart to order now — or talk to a Rev1 specialist and we’ll review your clinical application, BioMed resins, and package within one business day.

Reply within 1 business day We validate fit — not just take orders Authorized Formlabs reseller in the USA Dental & Medical Service Plans

Auburn Hills, Michigan's premier source for industrial 3D printers, 3D scanners, materials, and software. Serving engineers and manufacturers across North America.

Products
Company
Contact
Payment methods
AMEXApple PayGoogle PayPayPalShop PayUnionPayVISA
Pay over time

© 2026 Rev1 Technologies. All rights reserved.