CreatBotPro HS MotherboardGenuine CreatBot Replacement Part
Pro HS Motherboard for D600 Pro3 HS and D1000 Pro HS 3D Printers
The CreatBot Pro HS motherboard is the OEM main control board for the CreatBot D600 Pro3 HS and D1000 Pro HS large format 3D printers. The motherboard runs the printer: it drives the motion system, controls the hotends and heated components, and reads the printer's sensors. When a board fails, a genuine CreatBot replacement is the way to restore the printer to factory behavior. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot Pro HS Motherboard, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Signs your motherboard may need replacing
The printer will not boot, or boots without responding to the touchscreen.
Axes, heaters or fans stop responding while the parts themselves test good.
Visible damage on the board, such as burnt components or a damaged connector.
Other faults can look the same, for example a failed power supply, cable or driver. Contact Rev1 support before you order and we will help you confirm the board is the cause.
Choose your printer
| Printer option | Part number | Fits |
|---|---|---|
| D600 Pro3 HS | 111020 | D600 Pro3 HS, D1000 Pro HS |
| D1000 Pro HS | 111021 | D600 Pro3 HS, D1000 Pro HS |
Compatible CreatBot 3D printers
Fit is the same for both options. The D600 Pro2 HS and D1000 HS use a different board (111001 or 111002).
Which part number should I choose?
Pick the number that names your printer so the order matches your manual and service records. The board is the same either way. Note that these printers also use a Klipper host, which is a separate part: 111022 for the D600 Pro3 HS and 111023 for the D400 HS and D1000 Pro HS. It is not included with the motherboard. If you are not sure whether the fault is in the motherboard or the host, contact Rev1 support before you order.
Installation
Power the printer off and unplug it before opening the electronics bay. Photograph every connector before you disconnect anything, use anti-static precautions, and check the firmware with Rev1 support after installation. If your printer is under warranty, contact us first: Rev1 can perform the replacement as your certified CreatBot service provider.
CreatBot Pro HS Motherboard Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot Pro HS Motherboard — Questions
Which printer option do I need?
Choose the option that names your printer: D600 Pro3 HS (111020) or D1000 Pro HS (111021). It is the same board, so either one fits both.
Will it work in a D600 Pro2 HS?
No. The D600 Pro2 HS uses a different board, part 111001 or 111002.
Can Rev1 install it for me?
Yes. Rev1 is a certified CreatBot service provider and can diagnose, replace and test the board.
Is this a genuine CreatBot part?
Yes. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US, and every part we sell is a genuine CreatBot part.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.