CreatBotF430 Whole PlatformGenuine CreatBot Replacement Part
Whole build platform assembly for the CreatBot F430
The CreatBot F430 whole platform is the complete build platform assembly for the CreatBot F430 3D printer. It replaces the platform as one unit, so a warped, damaged or faulty platform can be swapped out without rebuilding it from separate components. CreatBot makes the F430 platform in two voltage versions, 110V and 220V, and you choose the one that matches your printer. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot F430 Whole Platform (Complete Build Platform Assembly), 110V and 220V, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Signs the platform needs replacing
First layers will not go down evenly, even after leveling and a clean build surface.
The platform is bent, cracked or damaged after a crash or impact.
The platform does not heat reliably and the fault traces back to the assembly itself.
Connectors or wiring on the platform are burnt or damaged.
Heating faults can also come from the power supply, main board, sensor or cabling. Contact Rev1 support if you want help confirming the platform is the cause.
Compatible CreatBot 3D printers
Both versions fit the F430. They differ only in voltage, so match the version to your printer's electrical configuration.
Choose your voltage
| Voltage | Part number | Fits |
|---|---|---|
| 110V | 181002 | F430 |
| 220V | 181001 | F430 |
Installation tips
Switch the printer off, unplug it and let the platform cool completely. Photograph the wiring before you disconnect it, and keep the mounting screws together. Fit the new platform, reconnect the wiring exactly as it was, and check that the cables do not snag through the full Z travel. Then level the bed and run a first layer test across the whole plate. The F430 is often used for engineering materials, so watch the first heated print closely.
Which voltage do I need?
Order the version that matches the platform already in your printer. The voltage is set by how the printer was configured for its market: printers supplied for North American mains power are normally 110V machines, and printers supplied for most other regions are normally 220V. The safest check is the rating label on the printer or the part number on your existing platform. If the printer was imported, bought used or converted, confirm before ordering, because fitting the wrong voltage platform can damage the platform or the printer electronics. Rev1 support can confirm the correct version from your printer's serial number.
CreatBot F430 Whole Platform (Complete Build Platform Assembly), 110V and 220V Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot F430 Whole Platform (Complete Build Platform Assembly), 110V and 220V — Questions
Which voltage do I need?
The same voltage as your printer and its current platform. Most F430 printers set up for US power are 110V (part 181002); 220V printers use part 181001. Check the rating label if you are unsure.
Does this platform fit the F430 NX?
These platforms are listed for the F430. Contact Rev1 support before ordering for any other model.
Is this a genuine CreatBot part?
Yes. Both versions are genuine CreatBot parts supplied by Rev1 Technologies, an authorized CreatBot dealer and certified service provider.
Why is there no photo of this part yet?
CreatBot has not supplied a product photo for this part yet. The part is identified by its CreatBot part number, and our team confirms it is the right part for your printer before it ships.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.