CreatBotF430 NX Heating PTCGenuine CreatBot Replacement Part
PTC chamber heater for the CreatBot F430 NX
The CreatBot F430 NX heating PTC is the chamber heater for the CreatBot F430 NX. It warms the air inside the enclosure so engineering materials cool slowly and evenly as they print. Without that warmth, materials like PC, nylon and ABS shrink unevenly, which shows up as lifted corners, split layers and dimensional drift. The heater is wired to mains power, so CreatBot makes a 110V version and a 220V version. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot F430 NX Heating PTC (Chamber Heater), from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Signs the heater needs replacing
The chamber stays cool with chamber heating on, or a heater error appears.
Warping returns on proven settings.
Visible damage or a burnt smell at the heater.
Compatible CreatBot 3D printers
Both versions fit only the F430 NX. The earlier F430 uses parts 173003 (110V) and 173004 (220V).
Why choose the genuine heater
Matched to the F430 NX. Same mounting and connections as the factory heater, so the swap is direct.
PTC element. A positive temperature coefficient heater draws less power as it warms, so it moderates its own output inside the enclosure.
Back to known results. Restoring chamber heat brings back the part quality your print profiles were tuned for.
Installation tips
Unplug the printer and wait for the chamber to cool. Photograph the connections, fit the new heater in the same orientation, secure the leads away from moving parts, and test chamber heating with the door closed.
Choose your voltage
| Voltage | Part number | Fits |
|---|---|---|
| 110V | 173001 | F430 NX |
| 220V | 173002 | F430 NX |
Choosing between 110V and 220V
The heater has to match the electrical configuration of your F430 NX. Machines delivered in North America are normally 110V; machines for most of Europe and Asia are 220V. Do not go by the region alone: the rating label on the printer or on the old heater is the reliable check. A heater on the wrong voltage will either barely warm the chamber or overheat. Rev1 can confirm the version from your serial number.
CreatBot F430 NX Heating PTC (Chamber Heater) Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot F430 NX Heating PTC (Chamber Heater) — Questions
Which voltage do I need?
The voltage your F430 NX runs on: part 173001 for 110V printers, part 173002 for 220V printers.
Is it the same heater as the F430?
No. The F430 uses parts 173003 and 173004.
Can Rev1 fit it?
Yes. Rev1 is a certified CreatBot service provider and can diagnose and replace the heater.
Why is there no photo of this part yet?
CreatBot has not supplied a product photo for this part yet. The part is identified by its CreatBot part number, and our team confirms it is the right part for your printer before it ships.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Is this a genuine CreatBot part?
Yes. It is CreatBot part 173001 / 173002, supplied by Rev1 Technologies, an authorized CreatBot dealer and certified service provider.