CreatBotF430 NX Cross Flow FanGenuine CreatBot Replacement Part
Cross flow (tangential) fan for the CreatBot F430 NX
The CreatBot F430 NX cross flow fan is the OEM cross flow fan for the CreatBot F430 NX 3D printer. Cross flow fans, also called tangential fans, draw air in along the full length of a long cylindrical impeller and push it out as a broad, even stream. CreatBot supplies the F430 NX fan in two voltage versions, 220V and 110V, so the replacement matches the electrical setup of your printer. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot F430 NX Cross Flow Fan, 110V and 220V Versions, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Compatible CreatBot 3D printers
Both versions fit the F430 NX only. The original F430 uses different cross flow fans, parts 150018 (220V) and 150019 (110V). The F430 NX sink fan is part 150007 and its cooling fan is part 150008.
Why replace a failing cross flow fan
Restore the designed airflow. The printer was built around this fan moving air across a wide area.
Stop the noise. A worn bearing hums, scrapes or rattles and only gets worse.
Avoid a sudden stop. Fans that start slowly or stall usually fail completely soon after.
Genuine CreatBot part. Same size, mounting and connector as the original F430 NX fan.
Installation tips
Unplug the printer before opening any cover. Photograph the fan, its mounting points and the connector, and double check that the voltage on the new fan matches the old one. Install it in the same orientation, spin the impeller by hand to make sure nothing rubs, then reassemble and confirm airflow at power on.
Choose your voltage
| Voltage | Part number | Fits |
|---|---|---|
| 220V | 150012 | F430 NX |
| 110V | 150013 | F430 NX |
110V or 220V: how to choose
Order the same voltage as the fan you are replacing. A printer running on standard North American 110V power normally takes the 110V version, part 150013. A printer configured for 220V supply takes part 150012. The voltage is usually printed on the fan label and on the printer's rating plate. Do not mix them: a fan on the wrong supply either runs poorly or fails early, and can stop working altogether.
CreatBot F430 NX Cross Flow Fan, 110V and 220V Versions Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot F430 NX Cross Flow Fan, 110V and 220V Versions — Questions
Which voltage do I need?
The voltage on your current fan: 110V is part 150013 and 220V is part 150012.
Will the F430 cross flow fan fit my F430 NX?
No. Order 150012 or 150013 for the F430 NX.
Is this a genuine CreatBot part?
Yes. Both versions are genuine CreatBot parts supplied by Rev1 Technologies, an authorized CreatBot dealer.
Why is there no photo of this part yet?
CreatBot has not supplied a product photo for this part yet. The part is identified by its CreatBot part number, and our team confirms it is the right part for your printer before it ships.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.