CreatBotF430 NX Chamber HeaterGenuine CreatBot Replacement Part
Build chamber heater for the CreatBot F430 NX
The CreatBot F430 NX chamber heater is the OEM heater for the build chamber of the CreatBot F430 NX. The F430 NX is built to print engineering and high performance materials, and many of them, from PC and nylon to PEEK, depend on a warm chamber to print well. Without chamber heat, parts cool unevenly, warp off the bed and crack along layer lines. CreatBot supplies this heater in two voltage versions, 110V and 220V. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot F430 NX Chamber Heater (Build Chamber Heater), 110V and 220V, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Compatible CreatBot 3D printers
Both versions fit the F430 NX and differ only in voltage. The original F430 uses different heaters, parts 182003 (110V) and 182004 (220V).
Why a reliable chamber heater matters
Controls warping on parts in materials that shrink as they cool.
Improves layer bonding, which is critical for strength in functional parts.
Repeatable results. A chamber that reaches temperature the same way every time gives consistent parts.
Genuine CreatBot part made for the F430 NX enclosure.
If the chamber is slow to heat, never reaches its set point or the printer shows a chamber heating error, the heater is a likely suspect. Rev1 support can help you rule out the sensor, fuse and wiring first.
Installation tips
Disconnect mains power and allow the chamber to cool. Photograph the wiring and terminals, swap the heater using the original hardware, and keep all leads secure and away from moving parts. Close the chamber, heat it and confirm the temperature rises and holds before you start a print.
Choose your voltage
| Voltage | Part number | Fits |
|---|---|---|
| 110V | 182001 | F430 NX |
| 220V | 182002 | F430 NX |
Which voltage do I need?
Order the voltage your F430 NX is configured for. In most cases that is the same as the heater you are replacing. Printers set up for North American mains power normally use 110V parts, while printers set up for most other regions use 220V parts. The rating label on the printer, or the part number on the old heater, will tell you for certain. Fitting the wrong voltage can stop the chamber heating properly or damage components, so if you are unsure, give Rev1 support your serial number and we will confirm the right part.
CreatBot F430 NX Chamber Heater (Build Chamber Heater), 110V and 220V Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot F430 NX Chamber Heater (Build Chamber Heater), 110V and 220V — Questions
Which voltage do I need?
The one your F430 NX runs on. US printers are normally 110V (182001). Printers configured for 220V use 182002.
Does the F430 heater fit the F430 NX?
CreatBot lists separate heaters for the two printers. Order the F430 NX part.
Is this a genuine CreatBot part?
Yes. Both versions are genuine CreatBot parts supplied by Rev1 Technologies, an authorized dealer and certified service provider.
Why is there no photo of this part yet?
CreatBot has not supplied a product photo for this part yet. The part is identified by its CreatBot part number, and our team confirms it is the right part for your printer before it ships.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.