CreatBotF430 Cross Flow FanGenuine CreatBot Replacement Part
Cross flow (tangential) fan for the CreatBot F430
The CreatBot F430 cross flow fan is the OEM cross flow fan for the CreatBot F430 3D printer. A cross flow, or tangential, fan uses a long barrel shaped impeller to move a wide, even curtain of air, which suits places where airflow has to cover a long span. CreatBot makes this fan in two versions, 220V and 110V, to match the power supply your F430 is set up for. Choose the voltage below. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot F430 Cross Flow Fan, 110V and 220V Versions, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Signs the cross flow fan needs replacing
No air, or noticeably less air, from the fan outlet while the printer runs.
Humming, scraping or rattling that gets worse over time.
The impeller turns roughly or rubs when spun by hand with the power off.
The fan starts slowly or stops by itself.
Compatible CreatBot 3D printers
Both versions fit the F430. The F430 NX uses its own cross flow fans, parts 150012 (220V) and 150013 (110V). Other F430 fans are the sink fan (150014), cooling fan (150015), drive cooling fan (150016) and filter fan (150017).
Choose your voltage
| Voltage | Part number | Fits |
|---|---|---|
| 220V | 150018 | F430 |
| 110V | 150019 | F430 |
Installation tips
Unplug the printer before you open any panel. Photograph the fan mounting and the connector, and confirm the voltage on the new fan matches the old one. Fit it in the same orientation, make sure the impeller spins freely, close the covers and check airflow at power on.
Choosing the right voltage
Match the fan to the voltage your printer runs on, which is normally the same as the original fan. Most printers in the United States run on 110V power and take the 110V version, part 150019. Printers set up for 220V supply take part 150018. Read the label on the old fan or the rating plate on the printer before you order. A fan of the wrong voltage will either run weak or not at all, or burn out quickly, so do not substitute one for the other.
CreatBot F430 Cross Flow Fan, 110V and 220V Versions Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot F430 Cross Flow Fan, 110V and 220V Versions — Questions
Which voltage do I need?
The same as your current fan and printer: 110V is part 150019 and 220V is part 150018. Check the label on the old fan if you are not sure.
Can I use the F430 NX cross flow fan?
No. The F430 NX uses parts 150012 and 150013. Order the fan listed for the F430.
Is this a genuine CreatBot part?
Yes. Both versions are genuine CreatBot parts supplied by Rev1 Technologies, an authorized CreatBot dealer.
Why is there no photo of this part yet?
CreatBot has not supplied a product photo for this part yet. The part is identified by its CreatBot part number, and our team confirms it is the right part for your printer before it ships.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.