CreatBotD600 Pro2 / D1000 Extruder PCB V1.2Genuine CreatBot Replacement Part
Extruder PCB V1.2 for D600 Pro2 and D1000 3D Printers
The CreatBot extruder PCB V1.2 is the circuit board on the print head of the CreatBot D600 Pro2 and D1000. The hotend heaters, temperature sensors, fans and extruder wiring connect to it and run back to the motherboard through the print head cable. Because so much meets on this one board, a fault here can make several healthy parts look broken at once. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot D600 Pro2 / D1000 Extruder PCB V1.2, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Signs the extruder PCB needs replacing
Heating, temperature reading or fan errors on the print head that stay with the board when you swap cables.
Intermittent faults that come and go as the print head moves across the bed.
A burnt component, a damaged connector or a cracked board.
A worn print head cable or a failed heater or sensor can cause similar symptoms. Contact Rev1 support and we will help you confirm the cause before you order.
Choose your printer
| Printer option | Part number | Fits |
|---|---|---|
| D1000 | 112012 | D600 Pro2, D1000 |
| D600 Pro2 | 112018 | D600 Pro2, D1000 |
Compatible CreatBot 3D printers
Fit is the same for both options. Other CreatBot printers use different extruder boards: the D600 Pro2 HS and D1000 HS use the HS board (112001 or 112002), and the D600 Pro uses its own V1, V2 or V3 board (112009, 112010, 112011).
Which part number should I choose?
Pick the number that names your printer so it matches your parts list and service records. The board is identical under both numbers. If you run a D600 Pro2 and a D1000, one spare board covers both. Before you order, check that the board in your printer is marked V1.2; if it carries a different marking, send Rev1 support a photo so we can confirm the right part.
Installation tips
Power the printer off, unplug it and let the hotend cool. Photograph every connector on the old board, use anti-static precautions and move the cables across one at a time. Check that each plug is fully seated and that no wire can rub against a moving part, then heat the hotend and run the fans before your first print.
CreatBot D600 Pro2 / D1000 Extruder PCB V1.2 Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot D600 Pro2 / D1000 Extruder PCB V1.2 — Questions
Which printer option do I need?
Choose the option that names your printer: D1000 (112012) or D600 Pro2 (112018). It is the same V1.2 board, so either one fits both.
Will it fit my D1000 HS?
No. The D1000 HS uses the HS extruder board, part 112001 or 112002.
Is this a genuine CreatBot part?
Yes. It is the OEM CreatBot extruder PCB V1.2, supplied by Rev1 Technologies, an authorized CreatBot dealer and certified service provider.
Is this a genuine CreatBot part?
Yes. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US, and every part we sell is a genuine CreatBot part.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.