CreatBotD600 Pro Drag Chain CableGenuine CreatBot Replacement Part
For the CreatBot D600 Pro
The CreatBot D600 Pro drag chain cable is the OEM cable that runs through the drag chain on the CreatBot D600 Pro. The drag chain guides the wiring for the moving assembly along a controlled bend, and this cable carries the power and signal lines that assembly relies on, such as heater, sensor, fan and motor connections. CreatBot built the D600 Pro with two versions of this cable, so it is offered here in V1 and V2. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot D600 Pro Drag Chain Cable, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
Signs the drag chain cable needs replacing
Temperature or heater faults that appear at some axis positions and clear at others.
A fan or sensor on the moving assembly that drops out during a print.
Errors you can trigger by moving the axis slowly by hand with the printer idle.
Cracked, flattened or worn insulation at the ends of the chain.
Every move of the axis bends this cable, so over time strands break inside the insulation. A replacement cable restores all conductors at once.
Choose your version
| Version | Part number | Fits |
|---|---|---|
| V1 | 160009 | D600 Pro |
| V2 | 160010 | D600 Pro |
Compatible CreatBot 3D printers
Both versions fit the D600 Pro; the correct one depends on how your machine was built. The D600 Pro2 (160013) and D600 Pro2 HS (160014) use different cables.
How to choose between V1 and V2
CreatBot revises parts during a model's production run, and the V1 and V2 cables match different builds of the D600 Pro. They are not interchangeable in every case, because connectors and routing can change between revisions. Look closely at the plugs on your existing cable, check any label on the old cable, or send Rev1 support your printer's serial number and a photo of both cable ends. We will confirm the right version before you order.
Installation tips
Power the printer off and unplug it. Label every connector and photograph the route before removal. Open the chain links, lay the new cable in the same channel without twisting it, and close the chain. Move the axis through its full travel by hand, then power up and check that temperatures, fans and sensors all read normally.
CreatBot D600 Pro Drag Chain Cable Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot D600 Pro Drag Chain Cable — Questions
Which version do I need?
It depends on your printer's build. Match the connectors on your old cable, or send Rev1 your serial number and photos and we will confirm V1 (160009) or V2 (160010).
Will either version fit a D600 Pro2?
No. The D600 Pro2 uses part 160013.
Is this a genuine CreatBot part?
Yes. Both versions are genuine CreatBot cables, supplied by Rev1 Technologies, an authorized CreatBot dealer.
Is this a genuine CreatBot part?
Yes. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US, and every part we sell is a genuine CreatBot part.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.