CreatBotD1000 / D1000 HS AC Power Control BoardGenuine CreatBot Replacement Part
D1000 AC Power Control Board for D1000 and D1000 HS 3D Printers
The CreatBot D1000 AC power control board is the OEM board that handles mains (AC) power inside the CreatBot D1000 and D1000 HS large format 3D printers. On machines of this size, the AC board switches mains power to the heating circuits that run directly from the wall supply, under the direction of the main control board. CreatBot sells this one board under two part numbers, one for each printer, so this listing offers both and you can pick the number that matches your machine. Full specifications →
Genuine CreatBot part, shipped from Rev1 — your authorized CreatBot dealer and service partner. Not sure it fits? Call (248) 707-2950.
Genuine CreatBot D1000 / D1000 HS AC Power Control Board, from an authorized CreatBot dealer.
An authentic CreatBot replacement part, not a third-party copy. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in Auburn Hills, Michigan.
One part, two CreatBot part numbers
CreatBot lists the board as 113002 for the D1000 HS and as 113007 for the D1000. CreatBot confirmed that both numbers are the same physical part, and each one fits both printers. Choose the number on your printer's parts list or your service records, and you receive the identical board either way.
Signs the AC power control board needs replacing
The heated bed or another AC heated zone will not heat, while the heater itself tests good.
Heating stays on or cuts out on its own, or the printer reports heating errors that point to the power stage.
Visible damage on the board, such as a scorched relay area, burnt components or a melted connector.
A failed heater, cable or main board can show the same symptoms. Contact Rev1 support before you order and we will help you confirm the cause.
Choose your printer
| Printer | CreatBot part number | Fits |
|---|---|---|
| D1000 HS | 113002 | D1000 HS, D1000 |
| D1000 | 113007 | D1000 HS, D1000 |
Compatible CreatBot 3D printers
Other models use different AC boards. The D600 Pro2 HS board is part 113001 and the F430 NX board is part 113003.
Which part number should I choose?
Either one. The two numbers exist because CreatBot catalogs the board separately for each printer, not because the boards differ. Most owners pick the number for their own printer so it matches their paperwork, but a D1000 owner who orders 113002 receives the correct board.
Installation tips
Switch the printer off and unplug it from the wall before you open the electronics bay, and give the power supply a few minutes to discharge. Photograph every connector and wire position before you disconnect anything, fit the new board in the same orientation, and check that every mains terminal is tight. Then power up and confirm each heater reaches its set point. If the printer is under warranty, contact Rev1 first.
CreatBot D1000 / D1000 HS AC Power Control Board Specifications
WHY REV1 TECH
Sold and Supported by Rev1 Technologies
Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US. Not sure which part your printer needs? Send us your printer model and serial number and our team will confirm the right part before it ships. We also handle installation, repair and preventive maintenance on CreatBot printers.
CreatBot D1000 / D1000 HS AC Power Control Board — Questions
Which printer number do I need?
Either. 113002 (D1000 HS) and 113007 (D1000) are the same board and fit both printers.
Will it fit my D600 Pro2 HS?
No. The D600 Pro2 HS uses part 113001.
Can Rev1 install it for me?
Yes. Rev1 Technologies is a certified CreatBot service provider and can diagnose, replace and test the board.
Is this a genuine CreatBot part?
Yes. Rev1 Technologies is an authorized CreatBot dealer and certified CreatBot service provider in the US, and every part we sell is a genuine CreatBot part.
How do I confirm it fits my printer?
Send us your printer model and serial number, or call (248) 707-2950, and our team will confirm the right part before it ships.
Can Rev1 install it for me?
Yes. We handle installation, repair and preventive maintenance on CreatBot printers. Ask us about on-site or depot service.