Formlabs Fuse X1 Recommended Production-Ready, Minimal Downtime
Everything in Basic plus a second Build Unit, a third Vacuum Conveyor, and the Fuse Blast Polishing System.
The Formlabs Fuse X1 Recommended Package adds what high-volume shops need: a second Build Unit so the next print starts while the last one cools, a third Vacuum Conveyor, and the Fuse Blast Polishing Module with agent, media, and mesh for smooth, semi-gloss, dye-ready parts — on top of Fuse X1, Fuse Sift X1, Mix Kit X1, Fuse Blast, and the Industrial Vacuum. Full specifications →
Rev1 quotes every Fuse X1 configuration with site planning, nitrogen and power requirements, installation, and operator training — call (248) 707-2950. *Formlabs lists Nylon 11 for Q1 2027 and Nylon 12 GF / TPU 90A for Q2 2027.

Factory-Built Precision. US-Supported by Rev1.
Fuse X1 is built and supported by Formlabs, with Production Service plans available. Rev1 adds application review, site planning, installation, operator training, and US-based support from our Auburn Hills, Michigan team.

Industrial SLS, without the industrial infrastructure.
Fuse X1 brings production-scale selective laser sintering to shops that could not justify a traditional industrial system: a fraction of the cost, less than half the floor space, and a workflow that installs in about an hour.
How teams use Fuse X1.
Quotes are from Formlabs’ published Fuse X1 case studies.



Deliver full-size parts overnight, or production runs of your latest design.
330 × 330 × 565 mm, 61.5 liters
Fuse X1’s build volume is 7.5× that of Fuse 1+ 30W (165 × 165 × 300 mm). With no support structures in SLS, parts nest throughout the whole volume, so one build can be a single full-scale prototype or thousands of production parts.



Scale production, not overhead, with 50% lower cost per part.
Formlabs’ published comparisons of Fuse X1 against outsourcing and legacy SLS, per part and lead time.
E-bike frame: $990 per frame, 3-day lead time
A full e-bike frame, one per build, costs $990 on Fuse X1 with a three-day lead time — versus $3,623 outsourced (14 days) and $3,010 on legacy SLS (5 days).



Productive no matter how you measure it.
Formlabs reports 3× higher throughput than competing industrial SLS and MJF systems in less than half the floor space.
More parts per build
With 30%+ packing density and a 61.5 L build volume, Fuse X1 fits more parts in a single build than competing industrial SLS and MJF systems — thousands more parts per week.
Fits where others can’t
At 1.3 m², Fuse X1 takes less than half the floor space of an HP 5600 (2.80 m²) or EOS P3 Next (2.70 m²), and it rolls through a standard doorway — no rebuilding your floor plan.
Scale your fleet as demand grows
Add printers one at a time. Formlabs states each additional Fuse X1 costs 3–5× less than other SLS and MJF printers, and low labor, minimal powder waste, and bulk powder pricing keep cost per part down as volume rises.
An industry-first, AI-powered print failure prevention system.
Formlabs calls Fuse X1 the most reliable SLS printer it has developed. These are the systems behind it.
Detect anomalies and mask them in real time
Computer vision combined with Adaptive Thermal Control detects anomalies as they happen and automatically masks the affected area, preventing print failures and maximizing part yield without sacrificing the rest of the build.
13 independent thermal zones
Thermal imaging collects and processes 700× more data per second than Fuse 1+ 30W, driving 13 independent thermal zones that hold powder at a precise, stable temperature from first layer to last — for packing freedom and consistent part quality.
A 120 W ytterbium fiber laser
A 120 W ytterbium fiber laser sinters each layer in a nitrogen environment, with Dynamic Dosing delivering the right amount of powder for every layer.
Cool outside the printer, start the next print
The wheeled, insulated Build Unit carries the print between Fuse X1 and Fuse Sift X1 with blind-mate power and data connectors; the print cools passively outside the printer so the next job can start with minimal downtime.
An industrial workflow anyone can run.
Install in an hour, start a print in five minutes.
Powder handling without the mess
The Vacuum Transport System loads used and new powder into Mix Kit X1 and refreshes the material for the next print, making loading as easy as printing.
Fuse X1, Formlabs’ largest SLS printer
Formlabs’ official launch video walks through the Fuse X1 printer, Build Unit, Fuse Sift X1, and the end-to-end SLS workflow.
Performance end-use thermoplastics, now at 50% lower part cost.
Formlabs powders start at $99/kg with bulk discounts, and bulk pricing goes as low as $45/kg. Formlabs lists Nylon 11 for Q1 2027 and Nylon 12 GF and TPU 90A for Q2 2027 on Fuse X1.

Fuse Sift X1 and Fuse Blast: from printed to polished in as little as 15 minutes.
Powder recovery, reimagined
Fuse Sift X1 holds 3 to 5 full builds of used powder. An integrated powder transport system moves used powder to Mix Kit X1 automatically, a compressed-air gun recovers powder from parts in seconds, the sealed glovebox keeps the workspace clean, and a parts hatch sends broken-out parts straight to a transfer bin.
Finished parts in 15 minutes
Fuse Blast delivers fully automated cleaning and polishing. An in-line ionizer keeps dust and media from re-settling, and the Polishing System produces a smooth, semi-gloss, dye-ready finish; versatile manual modes handle special parts.
Mix Kit X1
An automated blending system for fresh and reclaimed powder, so every build starts with a consistent, refreshed mix and minimal material waste.
Three ways to buy Fuse X1, each quoted by Rev1.
Each option has its own page, just as on Formlabs’ store — switch with the Package selector above. Formlabs recommends two Build Units for minimal downtime, and Production Service plans of 1, 3, or 5 years are available.



The Fuse X1 Recommended Package includes:
Fuse X1 vs. Fuse 1+ 30W.
Both are Formlabs SLS printers. Figures are from Formlabs’ published Fuse series comparison.
| Capability | Formlabs Fuse X1 | Formlabs Fuse 1+ 30W |
|---|---|---|
| Class | High-performance industrial | High-performance benchtop |
| Laser | 120 W fiber laser | 30 W fiber laser |
| Build volume | 330 × 330 × 565 mm (61.5 L) | 165 × 165 × 300 mm (8.2 L) |
| Throughput | 0.330 kg/hr | 0.063 kg/hr |
| Footprint | 1.3 m² (12.2 sq ft) | 0.4 m² (4.8 sq ft) |
| Print environment | Nitrogen | Air and nitrogen |
| Materials | Nylon 12; Nylon 11, Nylon 12 GF, TPU 90A coming; Open Material Mode | Nylon 12, 12 Tough, 12 White, 11, 12 GF, 11 CF, TPU 90A; Open Material Mode |
| At Rev1 | Quote | Quote |
For smaller SLS jobs and the widest powder range today, ask Rev1 about Fuse 1+ 30W. For resin parts, see the Formlabs Form 4L, or browse all SLS 3D printers and Rev1’s industrial 3D printer range.
Formlabs Fuse X1 Technical Data
RESOURCES
Downloads & Technical Support
Everything you need to evaluate and run Formlabs Fuse X1 with confidence.
WHY REV1 TECH
Authorized Formlabs Reseller. SLS & Resin Production Specialists.
Rev1 Technologies is headquartered in Auburn Hills, MI, with direct expertise in production resin workflows.