Formlabs Fuse Sift Extract, Recover, Mix — in One Station
Part extraction, powder recovery, storage, and automatic mixing for Fuse 1 Series SLS printers, in a single enclosed station.
Formlabs Fuse Sift is a safe, efficient powder recovery system for the Fuse 1+ 30W and Fuse 1. The free-standing station combines part extraction, powder recovery, storage, and mixing: dock the Build Chamber, break out parts under a negatively pressurized hood with a HEPA filter, and let Fuse Sift sieve used powder, dispense fresh powder, and mix the two for your next print — with up to 80% used powder. Full specifications →
Authorized Formlabs reseller in the USA — Rev1 helps you plan power, venting, and an NFPA 652-compliant vacuum for your Fuse Sift. Questions? Call (248) 707-2950.

Factory-Built Precision. US-Supported by Rev1.
Fuse Sift is built and supported by Formlabs as part of the Fuse Series. Rev1 adds site planning, vacuum selection, operator training, and US-based support from our Auburn Hills, Michigan team.

A seamless, contained environment for SLS powder.
Fuse Sift streamlines the Fuse Series workflow: parts come out, powder goes back in, and the next print is ready to go.



Extract parts, reclaim powder, and mix for the next print.
Break out the build cake under the hood
Dock the Build Chamber and unpack parts inside the enclosed work area. Formlabs specifies depowdering in about 10 minutes, with unsintered powder falling straight into recovery.
HEPA filtration and negative air pressure
Fuse Sift is equipped with a replaceable HEPA filter and a negatively pressurized hood with an independent venting system, keeping powder inside while you work with open access.
Dispense, mix, and store — automatically
Set the fresh powder amount and refresh ratio on Fuse Sift’s touchscreen; it dispenses, mixes, and stores used and fresh powder in its own hoppers, so every print starts from a controlled mix without manual weighing. Fuse Sift connects over Wi-Fi, Ethernet, or USB.
Low waste: reuse up to 80% used powder
Fuse Sift collects unsintered powder and filters out debris so it can go back into the next print. Formlabs cites competitive recyclability of up to 80% used powder, which keeps cost per part low.
Keep the printer running while Fuse Sift works.
Modular Build Chambers and Powder Cartridges move between the printer and Fuse Sift for a nonstop, cyclical workflow — even during cooldown.
Swap the Build Chamber, start the next print
When a build finishes, move its Build Chamber to Fuse Sift and load a second chamber into the printer. Parts cool and get unpacked while the next job prints.
Refill the Powder Cartridge from Sift
Fuse Sift fills Powder Cartridges with the mixed powder for the printer, so material handling stays inside the Fuse Series ecosystem.
Depowder in about 10 minutes
Formlabs’ Fuse workflow puts parts, powder, and tools in one place: unpack, recover, and get parts ready for media blasting or Fuse Blast.
The Fuse Series workflow in minutes
Formlabs’ video covers the basics of the Fuse Series, from software and materials to printing and post-processing with Fuse Sift.
Part of the Fuse Series.
Fuse Sift is designed for Fuse 1 Series printers and sits between the printer and finishing.



Built for the shop floor or the office
Fuse Sift is free-standing at 101.5 × 61.0 × 154.5 cm and 93 kg, and sits beside the printer to keep the powder loop short.
What to plan before installation.
From Formlabs’ Fuse Sift tech specs. Rev1 reviews these with you before delivery.
Power, vacuum, and environment
Fuse Sift needs a dedicated 120 VAC circuit: 15 A with a vacuum drawing under 12 A, or 20 A above that. It requires an auxiliary vacuum with static-dissipative components that is grounded and bonded (for example, an NFPA 652-compliant vacuum), and runs at 18–26 °C with ≤ 30% ambient humidity.



Fuse Sift ships with a full finishing toolkit.
Included accessories
Large brush, two small brushes, pipe cleaners, dental picks, gloves, dust mask, safety glasses, vacuum brush tool, vacuum crevice tool, and lifting straps.
Optional accessories: Fuse Sift Glovebox Panel and Parts Carrier. Ask Rev1 to add them to your order.
Powder handling across the Fuse 1+ 30W options.
How each Formlabs Fuse 1+ 30W option handles depowdering and powder recovery.
| Fuse 1+ 30W option | Depowdering & recovery included | Add Fuse Sift? |
|---|---|---|
| Printer | None (printer with Build Chamber) | Yes — for enclosed recovery and mixing |
| Starter Package | Fuse Depowdering Kit: workspace, tools, and 120 V sifter with 150 sieve | Upgrade path as volume grows |
| Complete Package | Fuse Sift and Fuse Blast included | Already included |
Browse all SLS 3D printers and post-processing.
Formlabs Fuse Sift Technical Data
RESOURCES
Downloads & Technical Support
Everything you need to plan and run Formlabs Fuse Sift with confidence.
WHY REV1 TECH
Authorized Formlabs Reseller. SLS & Resin Production Specialists.
Rev1 Technologies is headquartered in Auburn Hills, MI, with direct expertise in production resin workflows.