AUTOMATED SLS CLEANING & POLISHING • FORMLABS • REV1 TECH

Formlabs Fuse Blast Finished SLS Parts in 15 Minutes

Hands-off cleaning of a whole build chamber of SLS parts, with an optional Polishing System for smooth, dye-ready finishes.

Formlabs Fuse Blast automated cleaning and polishing station — front view

Formlabs Fuse Blast is a fully automated cleaning and polishing station for SLS 3D printed parts. Load a whole build chamber of parts from Fuse Sift into the tumbling basket and pre-programmed routines clean them in as little as 15 minutes, while an in-line ionizer keeps dust and media from re-settling. Formlabs reports it cuts post-processing labor time by 80%, and the optional Polishing System adds a smooth, semi-gloss, scuff-resistant, dye-ready finish in the same step. Full specifications →

15 minFull Build Chamber
80%Less Labor Time
45 cmTumbling Basket
8.3 LMedia Hopper
Works With
Fuse 1+ 30WFuse X1Fuse 1Third-Party PBF
Modes
AutomatedManual-AssistedHandheld
Upgrades
Polishing SystemHigh Capacity Kit

Authorized Formlabs reseller in the USA — Rev1 helps you size compressed air, add the Polishing System, and fit Fuse Blast into your Fuse workflow. Questions? Call (248) 707-2950.

Formlabs Fuse Blast automated cleaning and polishing station — front view
Rev1 Technologies · Authorized Formlabs Partner

Factory-Built Precision. US-Supported by Rev1.

Fuse Blast is built and supported by Formlabs as part of the Fuse Series. Rev1 adds compressed-air and site planning, operator training, and US-based support from our Auburn Hills, Michigan team.

Authorized Formlabs Reseller Site Planning & Training US Stock, Parts & Training
Formlabs — official manufacturer of Fuse Blast
FormlabsOfficial Manufacturer
Rev1 Technologies — authorized Formlabs reseller, Auburn Hills MI
Rev1 TechnologiesAuthorized Reseller
Why Choose Fuse Blast

100% hands-off cleaning and polishing for SLS parts.

Fuse Blast replaces manual bead blasting with repeatable, automated routines.

Gloved hand lifting cleaned SLS parts out of the Fuse Blast tumbling basket
Finished Parts in 15 Minutes
Routines post-process an entire build chamber in as little as 15 minutes, and passive filtering reduces media saturation to extend media life.
Operator selecting a cleaning routine on the Fuse Blast touchscreen
Consistent Results
Pre-programmed routines take out the guesswork, while manual mode adapts to any part requirement.
Professional Parts
An in-line ionizer delivers clean-to-the-touch parts; the Polishing System adds a smooth, semi-gloss, scuff-resistant, dye-ready finish.
Engineer holding a cleaned SLS printed intake manifold
Streamlined Post-Processing
Integrated into the Fuse ecosystem, Fuse Blast reduces labor time by 80%, according to Formlabs.
Features

Fast, automated, and consistent.

Automated Cleaning

Tumble and blast a full build at once

Parts tumble in a removable 45 cm basket while Fuse Blast runs a pre-programmed blasting routine. The basket fits a full Fuse build volume and lifts out without tools.

Pre-programmed routinesFull build volumeTool-free basket
Manual & Handheld Modes

Reach every surface on complex parts

Manual-assisted and handheld modes, controlled with foot pedals, let operators finish delicate features, deep channels, or oversized parts by hand inside the same sealed cabinet.

Foot-pedal controlHandheld nozzleAny part size
Blasting nozzle cleaning SLS parts inside the Fuse Blast tumbling basket

Sealed, workshop-friendly, clean to the touch

Fuse Blast is fully sealed, with a negatively pressurized hood, replaceable HEPA filter, and independent venting. An in-line ionizer prevents dust and media from re-settling, and passive recycling extends media life and speeds up processing on Fuse Sift.

Fully sealedIn-line ionizerHEPA filterPassive media recycling
Polishing System

Clean and polish in a single step.

The Fuse Blast Polishing System is a drop-in upgrade sold separately. It cleans and polishes parts straight from Fuse Sift without a second Blast cycle.

Smooth, Semi-Gloss Finish

Consumer-ready parts without chemicals

Polishing Media smooths parts by compacting the surface, unlike abrasive polishing or chemical surface melting, for a scuff-resistant, dye-ready finish with improved feel and appearance.

Semi-glossScuff-resistantDye-ready
Two SLS parts side by side: one polished with the Fuse Blast Polishing System, one only cleaned

Polished vs. cleaned

The Polishing Media is larger and propelled at higher pressure than standard glass media, and is designed to last more than a hundred Blast cycles while resisting the breakdown that occurs with glass media.

100+Cycles per media fill
7 mLAgent per 750 mL water
~6 hBlasting per dilution
Fuse Blast Polishing System module, media, agent, and fittings
Polishing System
The drop-in Polishing Module, with water tank and fittings, that turns Fuse Blast into a one-step clean-and-polish station.
Fuse Blast Polishing Media 4 L jug
Polishing Media 4 L (2.5 kg)
Specially formulated plastic beads for smooth, semi-gloss, dye-ready SLS parts.
Fuse Blast Polishing Agent 115 mL bottle with dosing syringe
Polishing Agent 115 mL
Conditions the media to improve polish quality and prevent clogging; diluted in the Polishing Module water tank.
Need end-use finishes?
Add the Polishing System to your Fuse Blast
Rev1 quotes Fuse Blast with the Polishing System, media, and agent, and can arrange a polished sample part in your material.
Workflow

From Fuse Sift to finished part.

Fuse Blast is the last step of the Fuse Series workflow: print, unpack and recover powder in Fuse Sift, then clean and polish in Fuse Blast.

Fuse 1+ 30W printer and Fuse Sift in a workshop

Straight from Fuse Sift

Move depowdered parts from Fuse Sift into Fuse Blast with the included transfer container, start a routine, and come back to clean parts — no manual bead blasting.

Transfer container includedHands-off routine
Watch the Video

Fully automated SLS post-processing

Formlabs’ video shows Fuse Blast cleaning and polishing a full batch of SLS parts.

Ecosystem

Works across the Fuse Series — and beyond.

Fuse Blast is compatible with Fuse X1, Fuse 1+ 30W, and Fuse 1, and with third-party powder bed fusion printers.

Formlabs Fuse X1 industrial SLS 3D printer
Fuse X1
Formlabs’ industrial SLS printer; pair with the High Capacity Kit. View Fuse X1 →
Formlabs Fuse 1+ 30W SLS 3D printer
Fuse 1+ 30W
The compact industrial SLS printer. View Fuse 1+ 30W →
Formlabs Fuse Sift powder recovery station
Fuse Sift
Unpack parts and recover powder before Fuse Blast. View Fuse Sift →
Fuse Blast Large Tumbler Basket from the High Capacity Kit

High Capacity Kit for larger batches

The optional High Capacity Kit is a drop-in Large Tumbler Basket that processes over 50% more parts per cycle than the standard basket, with a wider 400 mm opening and a spare liner kit. Formlabs recommends it for Fuse X1 users and multi-printer Fuse 1 Series fleets. It swaps in within minutes, with no tools.

50%+More parts per cycle
400 mmOpening
Site Requirements

What to plan before installation.

From Formlabs’ Fuse Blast tech specs. Rev1 reviews these with you before delivery.

Compressed Air
At least 10 SCFM at 90 PSI (285 SLPM at 6 bar), regulated to 90–120 PSI. Typically one 4 HP compressor.
Power
120 VAC, 6 A (US).
Environment
10–36 °C (50–96.8 °F), elevation up to 7,500 ft (2,286 m).
Footprint & Access
100 × 75 × 175 cm; 195 cm tall when open; allow 145 × 150 × 210 cm for convenient access.
Air Handling
Negatively pressurized hood with replaceable HEPA filter and an independent venting system.
Weight & Noise
164 kg (360 lb) without media; sound emission does not exceed 75 dB(A).
In the Box

Fuse Blast ships ready for your first batch.

Glass blasting media and the Polishing System are sold separately.

Transfer ContainerControl PedalsESD Wrist Strap7 mm Socket WrenchBlast Orifice (3 mm)Blast Orifice (4 mm)T-20 DriverFloor Mat
Compare

Fuse Blast with and without the Polishing System.

Both configurations use the same Fuse Blast; the Polishing System is a drop-in upgrade.

CapabilityFuse BlastFuse Blast + Polishing System
Surface resultClean to the touchSmooth, semi-gloss, scuff-resistant, dye-ready
Media200–300 µm glass media (13 kg hopper fill)Polishing Media (5.2 kg hopper fill), 100+ cycles
ProcessAutomated, manual-assisted, or handheld cleaningClean and polish in a single step, straight from Fuse Sift
ConsumablesGlass blasting mediaPolishing Media + Polishing Agent (7 mL per 750 mL water, ~6 h)
Best forFunctional prototypes, jigs, fixturesConsumer-facing and end-use parts

Browse all SLS 3D printers and post-processing.

Specifications

Formlabs Fuse Blast Technical Data

Printer Compatibility
Fuse Series SLS printers (Fuse X1, Fuse 1+ 30W, Fuse 1); third-party powder bed fusion printers
Dimensions (W×D×H)
100 × 75 × 175 cm (39 × 29.6 × 68.7 in); 195 cm (76.8 in) when open
Access Dimensions (W×D×H)
145 × 150 × 210 cm (57.4 × 59.6 × 82.6 in)
Weight
164 kg (360 lb) without blasting media
Media Hopper
8.3 L: 13 kg of 200–300 µm glass media, or 5.2 kg of Polishing Media
Waste Hopper
10.6 L
Tumbling Basket
45 cm internal diameter, 34.5 cm opening, 25 cm deep; removable without tools; fits a full Fuse build volume
Internal Work Area (W×D×H)
71 × 55 × 67 cm
Accessible Work Area
57 × 50 × 67 cm (basket removed)
Operating Environment
10–36 °C (50–96.8 °F); elevation up to 7,500 ft (2,286 m)
Air Handling
Negatively pressurized hood with replaceable HEPA filter; independent venting system
Power
120 VAC, 6 A (US)
Compressed Air
≥ 10 SCFM at 90 PSI (285 SLPM at 6 bar); regulate 90–120 PSI (6–8 bar); typically one 4 HP compressor
Connectivity
Wi-Fi (802.11 b/g/n), Gigabit Ethernet (RJ-45), USB 2.0 (C port)
Controls
Interactive touchscreen; foot pedals for manual control
Sound Emission
≤ 75 dB(A)
Included Accessories
Transfer container, control pedals, ESD wrist strap, 7 mm socket wrench, 3 mm and 4 mm blast orifices, T-20 driver, floor mat
SKU
FS1-FB-01

RESOURCES

Downloads & Technical Support

Everything you need to plan and run Formlabs Fuse Blast with confidence.

Fuse Blast Technical Data
Formlabs-published dimensions, hoppers, basket, compressed air, power, and connectivity.
View specifications →
SLS Finishing & Site Guide
Fuse Blast site requirements, media and Polishing System guidance, and the Fuse Series workflow.
Rev1 Technical Support
Application review, sample prints, and post-sales engineering guidance from Rev1 Technologies.

WHY REV1 TECH

Authorized Formlabs Reseller. SLS & Resin Production Specialists.

Rev1 Technologies is headquartered in Auburn Hills, MI, with direct expertise in production resin workflows.

YOUR REV1 PARTNER
AUTHORIZED FORMLABS RESELLER
01
Application Engineering
We review your parts, finish requirements, and compressed air before Fuse Blast arrives.
02
Onboarding & Training
Rev1 handles setup and operator training on PreForm, Dashboard, and the print-to-post workflow.
03
Ongoing Support
Direct access to Rev1’s technical team for resin guidance, troubleshooting, and maintenance.
04
Free Sample Print
Send us your STL. We’ll arrange a Formlabs SLS sample part, cleaned or polished, and ship it to you — or get an instant print quote.
05
In-Person Demo
Visit our Auburn Hills facility or schedule a demo at your site.
06
Consumables & Parts
Fuse Blast media, Polishing System consumables, HEPA filters, and Fuse spare parts — sourced and supported from the USA.
Buyer FAQ

Formlabs Fuse Blast — questions buyers ask.

How fast is Fuse Blast?
Formlabs specifies cleaning an entire build chamber of parts in as little as 15 minutes, and an 80% reduction in post-processing labor time.
Which printers does it work with?
Fuse X1, Fuse 1+ 30W, and Fuse 1, plus third-party powder bed fusion printers.
Is the Polishing System included?
No. The Polishing System is a drop-in upgrade sold separately, along with Polishing Media and Polishing Agent. Rev1 can quote them together with Fuse Blast.
What utilities does it need?
A 120 VAC, 6 A outlet and compressed air of at least 10 SCFM at 90 PSI, regulated to 90–120 PSI — typically a single 4 HP compressor.
Can I clean parts by hand?
Yes. Manual-assisted and handheld modes, run with the included foot pedals, let operators finish complex geometries inside the sealed cabinet.
What is the High Capacity Kit?
An optional Large Tumbler Basket that processes over 50% more parts per cycle with a 400 mm opening; Formlabs recommends it for Fuse X1 and multi-printer fleets.

FINISHED SLS PARTS, FASTER

Automate SLS finishing with Formlabs Fuse Blast

Talk to a Rev1 specialist about Fuse Blast — we’ll size compressed air, plan the Polishing System, and fit it into your Fuse workflow.

Reply within 1 business day We validate fit — not just take orders Authorized Formlabs reseller in the USA Site planning & training

Auburn Hills, Michigan's premier source for industrial 3D printers, 3D scanners, materials, and software. Serving engineers and manufacturers across North America.

Products
Company
Contact
Payment methods
AMEXApple PayGoogle PayPayPalShop PayUnionPayVISA
Pay over time

© 2026 Rev1 Technologies. All rights reserved.