Glass-Fiber Reinforced Filament — 3DXTech FibreX
FibreX is 3DXTech’s glass-fiber reinforced line — high stiffness like carbon fiber, but with more impact toughness, better elongation and, unlike carbon fiber, electrical insulation (GF is non-conductive). The range runs from Nylon 12+GF30 for wear and fatigue, through Obsidian Nylon 6+GF, to high-temp PEI/ULTEM+GF30 and PEEK+GF20 for aerospace and metal-replacement — plus FibreX ABS+GF in pellets for large-format printing. All 1.75 mm filament (except the pellets), made in the USA. This page compares the grades so you can match the polymer and the reinforcement to your part.
Comparing more widely? See all 3DXTech filament.
- Up to 8,790 MPa stiff
- Tough & impact-resistant
- Electrically insulating
- US stock

Choosing a 3DXTech fibrex machine
The decisions that actually matter for this class of machine — size them to your parts, not to a spec sheet.
Glass vs carbon fiber
Glass fiber adds stiffness and dimensional stability like CF but keeps more impact toughness and elongation, costs less, and stays electrically insulating — so choose GF for tough, load-bearing or non-conductive parts, and CarbonX when you need maximum rigidity and the lightest weight.
Match the polymer
Pick the base for the environment: Nylon 12+GF30 for wear, fatigue and low moisture uptake; Obsidian Nylon 6+GF for tough engineering parts; PEI/ULTEM+GF30 and PEEK+GF20 for the highest temperatures and aerospace service.
Stiffness & strength
FibreX runs from ~4,600 MPa (Obsidian PA6+GF) to ~8,790 MPa (PEI+GF30), with the PEI grade also the strongest at 145 MPa tensile — size the grade to the load and rigidity your part needs.
Hardware
Glass fiber is abrasive, so a hardened/wear-resistant nozzle is required. The PEI and PEEK grades also need a high-temp printer with a heated chamber; we confirm compatibility before you buy.
Compare the fibrex lineup
| Specification | Nylon 12+GF30 | Obsidian PA6+GF | PEI+GF30 | PEEK+GF20 |
|---|---|---|---|---|
| Base polymer | Nylon 12 (PA12) | Nylon 6 (PA6) | PEI — SABIC ULTEM | PEEK |
| Glass fiber | 30% | Glass-filled | 30% | 20% |
| Tensile strength | 82 MPa | 85 MPa | 145 MPa | 105 MPa |
| Tensile modulus (stiffness) | 7,800 MPa | 4,600 MPa | 8,790 MPa | 7,250 MPa |
| Heat resistance | High (PA12) | 176 °C HDT | 212 °C HDT (Tg 217 °C) | ~250 °C |
| Best for | Wear & fatigue | Tough engineering | Aerospace high-temp | Metal replacement |
| Price (from) | $107.80 | $143.00 | $137.50 | $247.50 |
Specs as published on each Rev1 product page / 3DXTech TDS. All glass-fiber reinforced, 1.75 mm, require a hardened nozzle. FibreX ABS+GF (listed below) is a pellet product for large-format/pellet printers.
3DXTech FibreX printers we sell & support





Built for the work you already do
Frequently asked questions
Glass fiber or carbon fiber — which should I choose?
Glass fiber (FibreX) and carbon fiber (CarbonX) both add stiffness and dimensional stability. Choose FibreX when you want more impact toughness and elongation, a lower cost, or electrical insulation (glass fiber is non-conductive). Choose CarbonX for maximum rigidity and the lightest weight. Tell us the part and we’ll recommend.
Which FibreX grade is right for me?
Match the base polymer to the environment: Nylon 12+GF30 for wear and fatigue, Obsidian Nylon 6+GF for tough engineering parts, PEI/ULTEM+GF30 for aerospace high-temp and the highest stiffness, and PEEK+GF20 for the ultimate heat and chemical resistance.
Do I need a special nozzle?
Yes — glass fiber abrades a standard brass nozzle, so a hardened or wear-resistant nozzle is required for every FibreX grade. The PEI and PEEK grades also need a high-temp printer with a heated chamber.
Is glass-fiber filament electrically conductive?
No — glass fiber is an insulator, so FibreX grades stay electrically insulating. That’s a key advantage over carbon-fiber grades for electrical and electronics parts where you don’t want conductivity.
Are these made in the US and in stock?
Yes — 3DXTech FibreX materials are made in the USA and ship from US stock. Rev1 is an authorized 3DXTech reseller with US-based application and printer support. Call (248) 707-2950.
Can’t find your answer? Browse the support knowledge base for setup, calibration and troubleshooting guides, or open a support ticket.
Print your part before you buy the printer
A free sample print or a live demo — either way you leave with a real part in hand and a same-day quote. Or browse the full lineup and filter by what your parts need.
Already own 3DXTech? Knowledge base & guides · Open a support ticket