Bambu Lab X1 Series LOGO LED Cable The Harness That Lights the Logo.
Genuine Replacement LOGO LED Cable for the X1 Series.
The LOGO LED Cable is the small wiring harness that carries power to the illuminated Bambu logo on the X1 series. It’s a twisted-pair cable with a keyed connector at each end that links the logo LED to the printer’s board. If the logo light has gone dark and the LED itself is fine, a broken or intermittent cable is a common cause — and this is the genuine part to swap in. Order it as a genuine Bambu Lab replacement. Full specifications →
Genuine Bambu part, stocked in the USA — ships from Rev1. Logo light out? Call (248) 707-2950 and we’ll help you check.
Genuine Bambu Lab Part. US Stock, Fast Shipping.
The X1 Series LOGO LED Cable is an authentic Bambu Lab replacement part, supplied and supported by Rev1 Technologies — your authorized Bambu Lab reseller in Auburn Hills, Michigan. Not a third-party clone.
A Small Cable With One Job.
The glowing Bambu logo on the front of an X1 is driven by a little LED, and this is the cable that feeds it. It’s a short twisted-pair harness with a keyed connector on each end — one to the logo LED, one to the board that powers it. Cables like this take a lot of small flexes over a printer’s life, and an intermittent or broken conductor is a routine reason a logo light flickers or goes dark. Swapping the genuine cable rules that out cleanly.
Keyed Connectors, Genuine Fit.
The connectors are keyed so they only seat the right way, and because it’s the genuine Bambu cable, the plugs match the sockets on the logo LED and the board exactly — no forcing, no wrong-pinout guesswork. It plugs straight in where the old one came out.
Built for the X1 Series.
This cable is for Bambu Lab’s X1 series — the X1 Carbon and X1E. Other Bambu printers route their lighting differently, so if you run a P1 or A1 machine, confirm the correct part with Rev1 before ordering. For an X1C or X1E with a dark logo, this is the genuine harness — and since it’s inexpensive, it’s an easy first thing to rule out.
Bambu Lab X1 Series LOGO LED Cable — Specs
WHY REV1 TECH
Authorized Bambu Lab Reseller. Additive Specialists.
Rev1 Technologies is an authorized Bambu Lab reseller in Auburn Hills, MI, supporting engineers, print farms, and manufacturers across the USA.
We stock the Bambu ecosystem and support it — from printers and filament to the small cables and spares that keep them running. Buy the replacement from a team that can help you fit it.
FAQ
Frequently Asked Questions
What does the LOGO LED Cable do?
It carries power to the illuminated Bambu logo LED on the X1 series. It’s a short twisted-pair harness with a keyed connector on each end — one to the LED and one to the printer’s board. It’s sold as a genuine replacement.
Which printers does it fit?
The Bambu Lab X1 series — the X1 Carbon and X1E. Other Bambu printers route their lighting differently, so if you run a P1 or A1 machine, contact Rev1 and we’ll confirm the right part before you order.
My logo light is out — is it the cable?
Often, yes — a broken or intermittent conductor in the cable is a common cause of a dark or flickering logo when the LED itself is fine. It’s an inexpensive part to rule out first. If you’re not sure, Rev1 can help you narrow it down.
Is it easy to replace?
Yes — because the connectors are keyed, the cable only plugs in one way, so replacement is a straightforward unplug-and-plug following Bambu Lab’s guidance. No soldering or rewiring.
Is this a genuine Bambu Lab part?
Yes. Rev1 Technologies is an authorized Bambu Lab reseller, and this is a genuine Bambu Lab cable — not a third-party substitute. The genuine harness has the correct connectors so it seats properly at both ends.
Can Rev1 help me diagnose it?
Yes — tell us what the logo light is doing and we’ll help you decide whether the cable is the fault, and point you to Bambu Lab’s official guidance. For US customers, buying from Rev1 means fast domestic shipping and a real person to call at (248) 707-2950.