Bambu Lab Anti-Vibration Feet Quieter Prints. Less Wear. A Steadier Machine.
Quieter Prints. Less Wear. A Steadier Machine.
A fast CoreXY printer moves a lot of mass quickly — and that energy travels straight into whatever it’s standing on as vibration and noise. Bambu’s Anti-Vibration Feet are single-piece molded TPU dampers that replace the printer’s stock feet and absorb that motion instead of transmitting it. The result is quieter operation, less vibration reaching your desk or shelf, and reduced load on the printer’s own mechanical components for steadier, more consistent prints. Ships as a pack of 8. Full specifications →
In stock in the USA — ships from Rev1. Running a farm and want to quiet the whole rack? Call (248) 707-2950.
Genuine Bambu Lab Part. US Stock, Fast Shipping.
These are authentic Bambu Lab Anti-Vibration Feet, supplied and supported by Rev1 Technologies — your authorized Bambu Lab reseller in Auburn Hills, Michigan. Not a third-party clone.
Absorb the Motion Instead of Passing It On.
The stock feet on most printers are rigid — they hold the machine in place but do little to isolate it. When the toolhead whips back and forth at speed, those vibrations pass straight into the surface below, where they turn into audible noise and can even nudge the printer over time. The molded TPU in these feet flexes to soak up that energy, keeping the machine planted and the workspace quieter.
Quieter Bench, Longer-Lasting Machine.
Less vibration reaching the desk means noticeably less noise — a real difference if your printer shares a room or an office. It also means less vibration echoing back into the printer’s own frame and motion system, which reduces wear on mechanical components and helps keep prints consistent. For a small, inexpensive part, it’s one of the most noticeable quality-of-life upgrades you can make.
A Two-Minute, No-Tools Swap.
Installation couldn’t be simpler: remove the four original feet from the bottom of the printer and press the new anti-vibration feet into the same spots. That’s it — no tools, no disassembly. The pack of 8 gives you a full set of four plus spares, or enough to do two printers.
For P1, X1, and P2S Printers.
These feet fit Bambu Lab’s P1P, P1S, X1 Carbon, X1E, and P2S printers, which share the same foot mounting. The newer H2 series uses a different foot design and has its own dedicated version. If you’re unsure which fits your machine — or you want to quiet down a whole shelf of printers — tell Rev1 your models and we’ll get you the right parts.
Bambu Anti-Vibration Feet — Specs
WHY REV1 TECH
Authorized Bambu Lab Reseller. Additive Specialists.
Rev1 Technologies is an authorized Bambu Lab reseller in Auburn Hills, MI, supporting engineers, print farms, and makers across the USA.
We stock and support the whole Bambu ecosystem — printers, filament, and the small upgrades that make them better to live with. Buy the feet from a team that can outfit a single machine or a whole print farm.
FAQ
Frequently Asked Questions
What do anti-vibration feet actually do?
They replace the printer’s rigid stock feet with flexible molded TPU that absorbs the vibration a fast printer generates instead of passing it into the surface below. In practice that means less audible noise, less vibration reaching your desk or shelf, and less energy echoing back into the printer’s own frame — which reduces wear on mechanical components and helps keep prints consistent.
How many are in a pack, and how many do I need?
Each pack contains 8 feet. A printer uses 4, so one pack gives you a full set plus spares — or enough to fit two printers. If you’re outfitting several machines, Rev1 can quote the quantity you need.
Is installation difficult?
Not at all — it takes about two minutes with no tools. Remove the four original feet from the bottom of the printer and press the new anti-vibration feet into the same locations. There’s no disassembly and nothing to calibrate afterward.
Which printers do these fit?
They fit the Bambu Lab P1P, P1S, X1 Carbon, X1E, and P2S, which share the same foot mounting. The newer H2 series uses a different foot design and has its own dedicated version. If you’re unsure which is right for your machine, tell Rev1 your model and we’ll confirm before you order.
Will they completely silence my printer?
They meaningfully reduce the vibration and noise transmitted into the surface the printer sits on — often the most noticeable source of noise in a quiet room — but they don’t eliminate every sound (fans and motion still make some noise). For the biggest improvement, pair them with a solid, heavy surface rather than a hollow or flexible table.
Are these genuine Bambu Lab parts?
Yes. Rev1 Technologies is an authorized Bambu Lab reseller, and these are genuine Bambu Lab Anti-Vibration Feet — molded to fit the stock foot mounts correctly, unlike generic clones that may not seat properly.