Rev1 ABS-GF
High-strength PETG with low warp, premium pigment, and tight dimensional tolerance for every 1.75mm direct-drive printer.
Rev1 PETG is a precision-extruded 1.75 mm filament made for production print farms and prosumer rigs. Vacuum-sealed with desiccant, wound on the same dimension-locked spool used by Bambu and Prusa drivers. 24 vibrant colors, matte and gloss finishes, 1 kg or 3 kg spools. Full specifications →
Colors shown are approximate — actual product color may vary slightly due to studio lighting, post-processing, and display calibration. if exact color match is critical to your project.
Ships same day from Auburn Hills, MI. Volume pricing on 10+ spools — talk to a material specialist for blended pallet rates.
… · Talk to a material specialist
Built for production. Priced for scale.
Rev1 PETG is what we'd buy for our own farm — dimension-locked, color-consistent, vacuum-sealed, and supported by humans in Auburn Hills, Michigan.
±0.03 mm tolerance
Every spool measured at extrusion. No high-low diameter spots, no surprise nozzle clogs from inconsistent filament feed.
UV-stable pigment loading
Premium colorants that don't shift hue mid-print or fade over the life of the part. Color today reads the same in 12 months.
Vacuum-sealed with desiccant
Each spool ships in a vacuum bag with silica. PETG arrives dry at your printer — drier filament means stronger layer bonds and fewer bubbles.
US fulfillment, US humans
Stocked in Auburn Hills, MI. Same-day ship cutoff 2 pm ET. Talk to a real material specialist on our team line — not a chatbot.
Dialed-in profile for direct-drive printers.
A starting profile that works on Bambu, Prusa, Voron, Creality, and Anycubic out of the box. Fine-tune nozzle temp ±5 °C and speed for your hardware.
| Nozzle Temperature | 230–250 °C |
| Bed Temperature | 70–80 °C |
| Print Speed | 40–60 mm/s |
| First Layer Speed | 20–25 mm/s |
| Retraction (direct) | 0.8–1.5 mm |
| Retraction (bowden) | 3–5 mm |
| Cooling Fan | 40–60 % |
| Enclosure | Optional |
| Drying (if exposed >2 days) | 65 °C / 4 hr |
Bed adhesion
Smooth PEI: no glue stick needed; clean with IPA. Textured PEI: works as-is. Glass: light glue stick or hairspray.
Stringing
PETG is mildly stringy by nature. Bump retraction by 0.2 mm and lower print temp by 5 °C if stringing persists. Coasting (0.05–0.1 mm) cleans up most travels.
Layer adhesion
PETG is forgiving on Z-bonding. If you see delamination, dry the spool (65 °C / 4 hr) and bump nozzle temp +5 °C — moisture is almost always the cause.
Bridging & overhangs
Lower fan slightly for steep overhangs (PETG benefits from heat); raise it for bridges. Verified on Bambu X1C, Prusa MK4, Voron 2.4, and Creality K1 default profiles.
Full Specifications
Mechanical, thermal, and print-setting data for this filament.
Need pallet pricing, TDS verification, or a blended-color order?
Sourced. Tested. Validated.
Rev1 Material is our in-house filament line — not a re-labeled spool from a single supplier, but a catalog curated through hundreds of evaluations.
Every formulation starts with a sourcing review across the global manufacturer base. Candidate materials are screened against mechanical and dimensional specifications, then put through dozens of benchmark prints on production-grade hardware — Bambu, Prusa, Voron, and our own farm printers — before any spool reaches the catalog.
By owning the curation process end-to-end, we deliver quality that competes with brand-name retail filament at price points the major labels can't match. Every Rev1 spool ships same-day from Auburn Hills, Michigan with documented dimensional tolerance and on-call support for production buyers.
Verified on the printers you actually own.
Rev1 PETG is profiled and bench-tested on the most common 1.75 mm direct-drive and bowden printers in production farms and prosumer setups.
Compatible with any 1.75 mm FFF printer capable of 230–250 °C hotend and 70–80 °C bed. Brand names are trademarks of their respective owners; compatibility verified on stock factory profiles.
Questions we get every day.
What temperature should I print Rev1 PETG at?
Start at 240 °C nozzle and 75 °C bed. Range is 230–250 °C / 70–80 °C depending on your printer's thermistor calibration and the part's geometry. Drop temp by 5 °C if you see stringing; raise by 5 °C if layer adhesion looks weak.
Do I need a heated bed?
Yes. PETG warps quickly without bed heat. 70–80 °C on a textured PEI or smooth PEI bed gives reliable first-layer adhesion without glue. Glass works too with a light coat of hairspray or gluestick.
How long does vacuum-sealed PETG stay print-ready?
6–12 months at room temperature with the original silica desiccant intact. Once opened, store in a dry box or PrintDry-style sealed container. If you see stringing or popping during print, dry the spool at 65 °C for 4 hours.
What's the price difference between 1 kg and 3 kg?
3 kg spools work out to roughly $21.65/kg versus $24.95/kg on 1 kg — about a 13 % per-kg savings, with the added benefit of fewer spool changes mid-print. For farms or long single prints, 3 kg is the better unit economics.
Can I get the technical data sheet?
Yes. The verified Rev1 PETG TDS is downloadable above in section 04 / Specifications. For ISO/ASTM-specific verification or RoHS/REACH declarations, contact a material specialist.
What's the same-day-shipping cutoff?
Orders for stocked colors placed before 2 pm ET ship same day from Auburn Hills, Michigan. Bulk orders (10+ spools) over multiple colors ship within 1 business day. Custom-color requests have a 1–2 week lead time.
Do you offer free samples?
Yes — we ship a small sample coil for color match verification on confirmed pre-pallet orders. Request a sample with the color name and intended project.
Talk to the Rev1 materials team.
Whether you're qualifying a single filament for production, sizing a multi-pallet recurring order, or just want to confirm a color match before you commit — there's a human ready to help.
Same-day ship out of Auburn Hills, Michigan. No purchase order minimums. No phone trees.
Dialed-in profile for direct-drive printers.
A starting profile that works on Bambu, Prusa, Voron, Creality, and Anycubic out of the box. Fine-tune nozzle temp ±5 °C and speed for your hardware.
| Nozzle Temperature | 230–250 °C |
| Bed Temperature | 70–80 °C |
| Print Speed | 40–60 mm/s |
| First Layer Speed | 20–25 mm/s |
| Retraction (direct) | 0.8–1.5 mm |
| Retraction (bowden) | 3–5 mm |
| Cooling Fan | 40–60 % |
| Enclosure | Optional |
| Drying (if exposed >2 days) | 65 °C / 4 hr |
Bed adhesion
Smooth PEI: no glue stick needed; clean with IPA. Textured PEI: works as-is. Glass: light glue stick or hairspray.
Stringing
PETG is mildly stringy by nature. Bump retraction by 0.2 mm and lower print temp by 5 °C if stringing persists. Coasting (0.05–0.1 mm) cleans up most travels.
Layer adhesion
PETG is forgiving on Z-bonding. If you see delamination, dry the spool (65 °C / 4 hr) and bump nozzle temp +5 °C — moisture is almost always the cause.
Bridging & overhangs
Lower fan slightly for steep overhangs (PETG benefits from heat); raise it for bridges. Verified on Bambu X1C, Prusa MK4, Voron 2.4, and Creality K1 default profiles.
Full Specifications
Mechanical, thermal, and print-setting data for this filament.
Need pallet pricing, TDS verification, or a blended-color order?
Sourced. Tested. Validated.
Rev1 Material is our in-house filament line — not a re-labeled spool from a single supplier, but a catalog curated through hundreds of evaluations.
Every formulation starts with a sourcing review across the global manufacturer base. Candidate materials are screened against mechanical and dimensional specifications, then put through dozens of benchmark prints on production-grade hardware — Bambu, Prusa, Voron, and our own farm printers — before any spool reaches the catalog.
By owning the curation process end-to-end, we deliver quality that competes with brand-name retail filament at price points the major labels can't match. Every Rev1 spool ships same-day from Auburn Hills, Michigan with documented dimensional tolerance and on-call support for production buyers.
Verified on the printers you actually own.
Rev1 PETG is profiled and bench-tested on the most common 1.75 mm direct-drive and bowden printers in production farms and prosumer setups.
Compatible with any 1.75 mm FFF printer capable of 230–250 °C hotend and 70–80 °C bed. Brand names are trademarks of their respective owners; compatibility verified on stock factory profiles.
Questions we get every day.
What temperature should I print Rev1 PETG at?
Start at 240 °C nozzle and 75 °C bed. Range is 230–250 °C / 70–80 °C depending on your printer's thermistor calibration and the part's geometry. Drop temp by 5 °C if you see stringing; raise by 5 °C if layer adhesion looks weak.
Do I need a heated bed?
Yes. PETG warps quickly without bed heat. 70–80 °C on a textured PEI or smooth PEI bed gives reliable first-layer adhesion without glue. Glass works too with a light coat of hairspray or gluestick.
How long does vacuum-sealed PETG stay print-ready?
6–12 months at room temperature with the original silica desiccant intact. Once opened, store in a dry box or PrintDry-style sealed container. If you see stringing or popping during print, dry the spool at 65 °C for 4 hours.
What's the price difference between 1 kg and 3 kg?
3 kg spools work out to roughly $21.65/kg versus $24.95/kg on 1 kg — about a 13 % per-kg savings, with the added benefit of fewer spool changes mid-print. For farms or long single prints, 3 kg is the better unit economics.
Can I get the technical data sheet?
Yes. The verified Rev1 PETG TDS is downloadable above in section 04 / Specifications. For ISO/ASTM-specific verification or RoHS/REACH declarations, contact a material specialist.
What's the same-day-shipping cutoff?
Orders for stocked colors placed before 2 pm ET ship same day from Auburn Hills, Michigan. Bulk orders (10+ spools) over multiple colors ship within 1 business day. Custom-color requests have a 1–2 week lead time.
Do you offer free samples?
Yes — we ship a small sample coil for color match verification on confirmed pre-pallet orders. Request a sample with the color name and intended project.
Talk to the Rev1 materials team.
Whether you're qualifying a single filament for production, sizing a multi-pallet recurring order, or just want to confirm a color match before you commit — there's a human ready to help.
Same-day ship out of Auburn Hills, Michigan. No purchase order minimums. No phone trees.
Need pallet pricing, TDS verification, or a blended-color order?
Sourced. Tested. Validated.
Rev1 Material is our in-house filament line — not a re-labeled spool from a single supplier, but a catalog curated through hundreds of evaluations.
Every formulation starts with a sourcing review across the global manufacturer base. Candidate materials are screened against mechanical and dimensional specifications, then put through dozens of benchmark prints on production-grade hardware — Bambu, Prusa, Voron, and our own farm printers — before any spool reaches the catalog.
By owning the curation process end-to-end, we deliver quality that competes with brand-name retail filament at price points the major labels can't match. Every Rev1 spool ships same-day from Auburn Hills, Michigan with documented dimensional tolerance and on-call support for production buyers.
Verified on the printers you actually own.
Rev1 PETG is profiled and bench-tested on the most common 1.75 mm direct-drive and bowden printers in production farms and prosumer setups.
Compatible with any 1.75 mm FFF printer capable of 230–250 °C hotend and 70–80 °C bed. Brand names are trademarks of their respective owners; compatibility verified on stock factory profiles.
Questions we get every day.
What temperature should I print Rev1 PETG at?
Start at 240 °C nozzle and 75 °C bed. Range is 230–250 °C / 70–80 °C depending on your printer's thermistor calibration and the part's geometry. Drop temp by 5 °C if you see stringing; raise by 5 °C if layer adhesion looks weak.
Do I need a heated bed?
Yes. PETG warps quickly without bed heat. 70–80 °C on a textured PEI or smooth PEI bed gives reliable first-layer adhesion without glue. Glass works too with a light coat of hairspray or gluestick.
How long does vacuum-sealed PETG stay print-ready?
6–12 months at room temperature with the original silica desiccant intact. Once opened, store in a dry box or PrintDry-style sealed container. If you see stringing or popping during print, dry the spool at 65 °C for 4 hours.
What's the price difference between 1 kg and 3 kg?
3 kg spools work out to roughly $21.65/kg versus $24.95/kg on 1 kg — about a 13 % per-kg savings, with the added benefit of fewer spool changes mid-print. For farms or long single prints, 3 kg is the better unit economics.
Can I get the technical data sheet?
Yes. The verified Rev1 PETG TDS is downloadable above in section 04 / Specifications. For ISO/ASTM-specific verification or RoHS/REACH declarations, contact a material specialist.
What's the same-day-shipping cutoff?
Orders for stocked colors placed before 2 pm ET ship same day from Auburn Hills, Michigan. Bulk orders (10+ spools) over multiple colors ship within 1 business day. Custom-color requests have a 1–2 week lead time.
Do you offer free samples?
Yes — we ship a small sample coil for color match verification on confirmed pre-pallet orders. Request a sample with the color name and intended project.
Talk to the Rev1 materials team.
Whether you're qualifying a single filament for production, sizing a multi-pallet recurring order, or just want to confirm a color match before you commit — there's a human ready to help.
Same-day ship out of Auburn Hills, Michigan. No purchase order minimums. No phone trees.
Sourced. Tested. Validated.
Rev1 Material is our in-house filament line — not a re-labeled spool from a single supplier, but a catalog curated through hundreds of evaluations.
Every formulation starts with a sourcing review across the global manufacturer base. Candidate materials are screened against mechanical and dimensional specifications, then put through dozens of benchmark prints on production-grade hardware — Bambu, Prusa, Voron, and our own farm printers — before any spool reaches the catalog.
By owning the curation process end-to-end, we deliver quality that competes with brand-name retail filament at price points the major labels can't match. Every Rev1 spool ships same-day from Auburn Hills, Michigan with documented dimensional tolerance and on-call support for production buyers.
Verified on the printers you actually own.
Rev1 PETG is profiled and bench-tested on the most common 1.75 mm direct-drive and bowden printers in production farms and prosumer setups.
Compatible with any 1.75 mm FFF printer capable of 230–250 °C hotend and 70–80 °C bed. Brand names are trademarks of their respective owners; compatibility verified on stock factory profiles.
Questions we get every day.
What temperature should I print Rev1 PETG at?
Start at 240 °C nozzle and 75 °C bed. Range is 230–250 °C / 70–80 °C depending on your printer's thermistor calibration and the part's geometry. Drop temp by 5 °C if you see stringing; raise by 5 °C if layer adhesion looks weak.
Do I need a heated bed?
Yes. PETG warps quickly without bed heat. 70–80 °C on a textured PEI or smooth PEI bed gives reliable first-layer adhesion without glue. Glass works too with a light coat of hairspray or gluestick.
How long does vacuum-sealed PETG stay print-ready?
6–12 months at room temperature with the original silica desiccant intact. Once opened, store in a dry box or PrintDry-style sealed container. If you see stringing or popping during print, dry the spool at 65 °C for 4 hours.
What's the price difference between 1 kg and 3 kg?
3 kg spools work out to roughly $21.65/kg versus $24.95/kg on 1 kg — about a 13 % per-kg savings, with the added benefit of fewer spool changes mid-print. For farms or long single prints, 3 kg is the better unit economics.
Can I get the technical data sheet?
Yes. The verified Rev1 PETG TDS is downloadable above in section 04 / Specifications. For ISO/ASTM-specific verification or RoHS/REACH declarations, contact a material specialist.
What's the same-day-shipping cutoff?
Orders for stocked colors placed before 2 pm ET ship same day from Auburn Hills, Michigan. Bulk orders (10+ spools) over multiple colors ship within 1 business day. Custom-color requests have a 1–2 week lead time.
Do you offer free samples?
Yes — we ship a small sample coil for color match verification on confirmed pre-pallet orders. Request a sample with the color name and intended project.
Talk to the Rev1 materials team.
Whether you're qualifying a single filament for production, sizing a multi-pallet recurring order, or just want to confirm a color match before you commit — there's a human ready to help.
Same-day ship out of Auburn Hills, Michigan. No purchase order minimums. No phone trees.